Gym Dandy®
NOTE:
Please read all instructions
carefully before using this
product
TEETER TOTTER
TT-360
Table of Contents
Safety Notice
Important Assembly
Information
Care and Maintenance
Parts List
Warranty
Ordering Parts
Model
TT-360
Retain This
Manual for
Reference
IMPORTANT: Please read this manual before commencing
assembly of this product.
IMPEX® INC.
2801 S. Towne Ave, Pomona, CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
111228
OWNER'S
MANUAL
This play ground equipment is built for optimum safety. However, certain precautions apply
whenever you operate a piece of play ground equipment. Be sure to read the entire manual before
you assemble or operate your equipment. In particular, note the following safety precautions to
reduce the likelihood of serious or fatal injury.
1. Children must be supervised at all times and never left unattended with the unit.
2. Do not install the equipment over concrete, asphalt, packed earth, grass, carpet or any other
hard surface. A fall onto a hard surface can result in serious injury to the user.
3. Make sure the surfaces, either indoors or outdoors, are free of objects that may cause tipping
over.
4. Place the equipment on level ground, not less than 6 ft (1.8 m) from any structure or obstruction
such as fence, garage, house, overhanging branches, laundry lines, or electrical wires.
5. Make sure bystanders are at least 5 feet away from the equipment while it is in motion. No one
should be allowed to walk close to, in front of, behind, or between moving items.
6. Keeps hands and feet away from the pivot area.
7. Do not get off from seat while it is in motion.
8. Do not stand on the teeter-totter. This could cause damage to the ride and result in injury.
9. Do not swing with empty seat.
10.Children should not wear loose clothing. Attire should include well-fitting shoes.
11.This teeter totter is intended for use by children from ages 3 to 13.
12.Maximum weight capacity 300 lbs.
13.Only two persons should be using the equipment at the same time.
14.Impact-absorbing material must be placed around the teeter totter. Please refer to the
PLAYGROUND SURFACING MATERIALS in page 3.
15.Maximum fall height: 52 inches.
16.To prevent serious injury, children must NOT use the equipment until properly installed.
17.To prevent serious injury, parents must make warnings to children not to use this equipment in a
manner other than intended.
18.To prevent serious injury, parents must make warnings to children not to attach items to the
equipment that are not specifically designed for use with the equipment.
19.Lock this Teeter Totter with Cable Strap when not in use.
20.This Teeter Totter is for Home Use only.
SAVE THESE INSTRUCTIONS.
CONSUMER INFORMATION SHEET FOR
PLAYGROUND SURFACING MATERIALS
2
The U.S. Consumer Product Safety Commission (CPSC) estimates that about 100,000 playground equipment-
related injuries resulting from falls to the ground surface are treated annually in U.S. hospital emergency rooms. Injuries
involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be
fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major
factor in determining the injury-causing potential of a fall. It is self evident that a fall onto a shock absorbing surface is less
likely to cause a serious injury than a fall onto a hard surface. Playground equipment should never be placed on hard
surfaces such as concrete or asphalt and while grass may appear to be acceptable it may quickly turn to hard packed
earth in areas of high traffic. Shredded bark mulch, wood chips, fine sand or fine gravel are considered to be acceptable
shock absorbing surfaces when installed and maintained at a sufficient depth under and around playground equipment.
The following table lists the maximum height from which a child would not be expected to sustain a life-threatening
head injury in a fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of 6, 9,
and 12 inches. However, it should be recognized that all injuries due to falls cannot be prevented no matter what
surfacing material is used.
FALL HEIGHT IN FEET FROM WHICH A LIFE THREATENING HEAD INJURY
WOULD NOT BE EXPECTED
TYPE OF MATERIAL
Double Shredded Bark
Mulch
6-INCH DEPTH 9-INCH DEPTH 12-INCH DEPTH
6
6
5
6
10
7
11
12
9
Wood Chips
Fine Sand
. .
5
Fine Gravel
7
10
It is recommended that a shock absorbing material should extend a minimum of 6 feet in all directions from the
perimeter of stationary equipment such as climbers and slides. However, because children may deliberately jump from a
moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2 times
the height of the pivot point measured from a point directly beneath the pivot on the supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of various material. No
particular material is recommended over another. However, every material is only effective when properly maintained.
Materials should be checked periodically and replenished to maintain correct depth as determined necessary for your
equipment. The choice of a material depends on the type and height of the playground equipment, the availability of the
material in your area, and its cost.
'This information has been extracted from the CPSC publications "Playground Surfacing - Technical Information Guide" and
"Handbook for Public Playground Safety:' Copies of these reports can be obtained by sending a postcard to the: Office of Public Affairs,
U.S. Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hot line: 1-800-638-2772.
3
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Base Frame. If the labels are missing or illegible, please
call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
IMPORTANT ASSEMBLY INFORMATION
4
Tools Required for Assembly: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended that this equipment is assembled by two or more
people to avoid possible injury.
Ensure Carriage Bolts are inserted through the SQUARE holes on components that need to
be assembled. Attach washer only to end of the Carriage Bolt.
Use Allen Bolts or Hex Bolts inserted through the ROUND hole on components that need to
be assembled.
Always wait until all bolts are assembled onto the bench before tightening the bolts. Do not
tighten each bolt right after it is installed
Fasten Nuts and Bolts
Securely tighten all Nuts and Bolts after all
components have been assembled in current and
previous steps.
NOTE: Do not over tighten any component with
pivoting function.
Make sure all pivoting components are able to move
freely.
Do not tighten all Nuts and Bolts in this step.
CARE AND MAINTENANCE
5
1. Periodically inspect all parts. Check all nuts and bolts twice monthly during the usage season
for tightness and tighten as required. It is particularly important that this procedure be
followed at the beginning of each season.
2. Replace any worn and damaged part immediately. Check all coverings for bolts and sharp
edges twice monthly during usage season to be certain they are in place. Replace when
necessary. It is especially important to do this at the beginning of each new season.
3. Cover the equipment with tarp when left outdoor.
4. Use mild household spray cleaners and/or a damp rag to wipe clean. Do not use harsh
cleaning chemicals.
5. Sand rusted areas on tubular members and repaint using a non-lead based paint meeting the
requirements of Title 16 CFR Part 1303.
6. Disposal Instructions – The equipment can be safely disassembled and disposed without
unreasonable hazards. Call your local recycle agency regarding details of recycling.
7. Failure to examine regularly may affect the safety level of the equipment.
WEIGHT CAPACITY AND DIMENSION
1. Maximum weight capacity: 300 lbs.
2. Assembled Dimension: 99” x 38” x 45”
3. Space required to operate this equipment: 18 ft x 18 ft
PARTS LIST
PART
DESCRIPTION
SIZE
QUANTITY
6
NO.
1
2
3
Base Stabilizer
Base Frame
Center Post
2
1
1
4
5
6
7
Middle Arc Tube
Seat Support
Pivot Support
Handle Post
Seat Pad
1
1
1
2
8
2
9
Back Pad
2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Axle
M12 x 4 7/8”
Ø 1” x Ø 1 5/8”
1
2
2
2
2
2
1
1
2
1
2
1
4
4
4
2
16
4
2
4
4
4
19
2
24
8
15
2
Metal Bushing
Roller Wheel
Nut Cap
Ø ½”
Ø ½” x Ø 1 3/8”
Ø 2 1/8”
Spacer
Seat Support Tube End Cap
Nylon Spacer
Curved Bracket
Curved Bracket
Ball Bearings
Ball Bearings
U-shaped Bracket
Handle End Cap
Nut Cap
Handle Grip
Handle
Allen Bolt
Allen Bolt
6 ¼” x R25
4 ¾” x R28
51208
6205
5 ½” x 3 ½”
Ø 1 ”
Ø 3/8”
4 3/8”
M10 x 3”
M10 x 2 ¾”
M10 x 1 ¾”
M8 x 2 1/8”
M10 x 2 ¼”
M8
M10
M12
Ø ¾”
Ø 5/8”
Allen Bolt
Allen Bolt
Carriage Bolt
Aircraft Nut
Aircraft Nut
Aircraft Nut
Curved Washer
Curved Washer
Flat Washer
Handle End Cap
Lock Washer
Cable Strap Bracket
Cable Strap
Ø ¾”
Ø 1 5/8”
Ø ¾”
8
1
1
1
6 ¼” x R25
Seat Support With Cable Bracket
L-shaped Lock Pin
1
7
IMPEX® INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to
replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an
IMPEX authorized service center or for products used for commercial or rental purposes. No other
warranty beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX® INC.
2801 S. Towne Ave.
Pomona, CA 91766
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
10
|