Fully Automatic Washing Machine
Operation Manual
MODEL: AW60-9021
NAMES OF RESPECTIVE PARTS
Simple installation
The washing machine should be placed inside the room with a flat floor, which is
convenient for water supply and drain, has low moisture and no direct sunshine, and does
not freeze in winter.
Please adjust the washing machine even according to the instructions below to make the
washing machine run steadily in low noise.
1.
Loosen the fixing pole on the adjusting foot, screw in or screw out the adjusting foot
to make the four foot placed even on the floor.
2.
When the floor is slanting or uneven, it is not easy to make even only by the
adjusting foot. Then the rubber band can be added to the unflat place.
Use gradienter to check whether the washing machine is placed flat.
After the adjustment the fixing pole should be screwed back and tight.
3.
4.
Notices:
If the washing machine is not placed flat (the inclination angle is over 2o), it may
cause great vibration or automatic check and rectification or other abnormal circumstances
will often take place in the course of spinning.
1. Top lid
2. Washing tub
3. Gradienter
4. Operation panel 5. Filter
9. Drain hose
6.
Adjustable foot
.
7. Pulsator
8. Top frame
Base foam
Bubble
Adjustable foot
Loose
Screw in
Fixing pole
(Part of standardmachine)
Accessories
Tight
Screw out
Fixing ring(1) is used for the
fixation in time of the installation
of the drain hose
Gradienter mark
Base cover (1)
Self-tapping screw (1)
Water inlet hose assembly(2)
Universal connector(2)
Drain hose (1)
3
4
SIMPLE INSTALLATION
SIMPLE INSTALLATION
Installation of drain hose
Installation of the water inlet hose
1. Check the tap mouth. If it is not even, it can be filed even.
Nip the fixing ring with hand to make it loose and engaged on
the drain hose and put the drain hose into the leading skirt of drain
hose in the bottom of the washing machine to the end at the most
(soak the head of the drain hose in warm water, it will make the
engagement easy), and loose the fixing ring to let it clasp the drain
hose.
2. Screw loose the locking ring, but do not let the locking ring drop off. Screw the four screws at the same
distance.
Cabinet
Inner hose
3. Put the universal connector into the tap and stick to the tap mouth at the most and then screw in the screws.
4. Screw tight the locking ring to the right.
Fixing ring
5. Pull the skirt of one end of the water inlet hose downwards, and then plug in the universal connector. Asound of
"KA-TA" means proper connection.
It had better put the outlet of the drain hose into the nearby
drainage permanently, which can save the trouble that the drain
hose has to be connected each time before use. If the drainage is
far from the washing machine, it can be solved by connection of the
drain hoses head with end to extend.
Drain hose
6. Grasp the water inlet hose by hand and pull it downward to see whether it is secured
7. Screw the nut on the other end of the water inlet hose into the water inlet of the washing machine to the most.
Leading ring
Tap
File
Locking ring
If the calibre of the tap
is big, the connecting
ring can be taken off.
Notices:
Connecting ring
Drain faults will be caused when the drain hose is blocked.
Skirt
Notices:
After end of inlet hose installation, do not immediately switch on the power. Open the tap and let water go
over both ends of the inlet hose and check whether occur the leakage. If the inlet hose is difficult to install
because of the tap , you can invite the experienced person for help.
The method of installation for the double water inlet hose is same.
6
5
SIMPLE INSTALLATION &OPERATION
SIMPLE INSTALLATION
Installation of the base cover
1. Slant the washing machine with angle of 45o in the direction of the arrows showed in the figure, put the
side with the clasper to the washing machine and the other side to the ground, insert back lid along the
direction of the upper slot of the base from the back side of the washing machine.
2. Put the base cover straight to the point and then press the back lid
Power source and grounding
The washing machine employs alternative current with the rated voltage 230V and
frequency 50 Hz. When the voltage fluctuates between 196V--252V, the washing machine can
work normally. A special power socket to be provided beside the washing machine for
convenience and safety. The method of connection of the socket is as the figure below:
upward till there is a sound of "Gaba" and then screw in a self-tapping screw.
Slot
Base cover
Hole for Self-tapping screw
Notices:
The socket and the grounding wire must be installed by an electrician to prevent
incorrect installation or use of the socket, and to guarantee the safety of use of
electricity.
The power wire of the washing machine employs Y connection and the
replacement of the power wire should be carried out by professionals.
No connection of the grounding wire with the neutral wire, otherwise the cabinet
will be charged, which is likely to cause the danger of electric shock.
Simple operation
1. Before operation, please open the splash-free cover.
2. Put the clothes into washing tub and close the splash-free cover.
3. Put the detergent into the water inlet case.
4. Plug the cord into the socket, switch on the power.
5. Turnon the tap connected to the two water inlet hoses.
6. Press "Power" button.
7. Press "Start/Pause" button. The washing machine will go into operation automatically as
programmed.
Grounding wire
Rated voltage ~220V
Remark: If you want to set other programs, please see and read "Way of use".
7
8
FUNCTIONS OF BUTTONS
FUNCTIONS OF BUTTONS
Selection of water level
Start / Pause
Temperature
To set water level according to the
quantity of clothes. Each press, the
water level indicator light moves in
turn.
After program selection, press the
button to start. The flashing light
indicates the selectedprograms and
the current state. Press the button
again for pause. The program
continues at anotherpress till the
program is finished.
Press the button to set the wash
mode of injection HOT or COLD
water for wash. When the lights of
HOT and COLD are light at the
same time, the HOT water and
COLD water are injecting.
Press the button you can select
HOT, COLD and WARM water to
be used.
6.0
Child Lock
Please read "Additional explanation"
Function
Press the button to select
"WASH"+"RINSE"+"SPIN",
"SOAK"+"WASH"+"RINSE"+"SPIN",
"WASH","WASH"+"RINSE",
"RINSE"+"SPIN","SPIN".
Delay
Power switch
Press the buttonto set up
beginning time ofwashing. Each
press the buttonaccompany a
change of anhour in indicator
within 24h. After 24h, eachpress
The power socketis plugged in, press the
button, the washerenters to workingstate and
Program setting
automatically set upfor standard program.
In the courseof working, pressthe button toend
Six washing programs are available. The chosen programs are
current program, thewasher enters tostopping
appearance state.
the button add6 hours until48h.
No use thedelay time function, it
displayed by indicator lamp. The lamp of "FUZZY, ECONOMY,
DELICATE" is light. The lamp of "BULKY, WOOL, ANTI-WRINKLE"
is flash.
shows the programremaining time.
A
There is no further notice for slight change of above picture.
In order to protect controller, the interval of power on and off
r
should be more than 30 seconds.
9
10
WAY OF USE
Fully automatic program
Programs
Application
Rinse times
Total time
Spin time
Washing time
Good washing ability.
12 mins
Twice
Fuzzy
6 mins
About 41 mins
About 10 mins
It can be chosen in every season.
Mainly for summer season or not dirt clothes
Economy washing means shorter time
Economy
1 times+Spray
2 mins
1 mins
Suitable for delicate and high-grade clothes
Delicate
Bulky
About 33 mins
About 47 mins
2 mins
7 mins
Twice
Twice
Twice
Twice
10 mins
15 mins
Strong washing ability appliable for
heavily-stained items and bulky items
The program for wool
15 mins
8 mins
Wool
About 34 mins
About 27 mins
Drain only
Drain only
The program for anti-wrinkle clothes.
Anti-wrinkle
Remark: 1. Don t include economy program, the upper time table have been reserved water injection time (2 minutes / times) and drain time (1 minutes / times).
2. Before select the hot water for wash, you need read the notice label of clothes.
Additional explanation
1. "CHILD LOCK" function: After start, press the "FUNCTION" and "WATER LEVEL" button at the same time, then all buttons will be locked (include the "POWER" button), the indication is displayed "CL" a second every 5 seconds. Press
the "FUNCTION " and "WATER LEVEL" button at the same time to unlock the function.
2. In the course SOAK ,the washer does not stop completely, it will wash interval to let the washing evenly mix with the detergent.
3. If you have selected the "Fuzzy" program, the washer can detect texture of clothes to change intensity of wash and according to the temperature of water adjust the time of wash.
4. The washing machine has an inbuilt memory,thus ensuring the machine will start from the same point where it has stopped,on resumption of power supply.If you don't want the machine
come back to the last process where power failed last time on the condition of the power restoration, you only need do is to re-start the power button.
11
12
WAY OF USE
Delay time program
WAY OF USE
1. Dissolve the detergent with proper amount of warm water (below 50 ), then pour it into
Method of use of "Delay" button
the washing machine.
2. Fold up the blanket as the method showed in the figures below and put it into the washing
Delay time means the beginning time of washing.
1. Switch on "Power" button.
In each press of the button, the preset
time changes by one hour within 24h.
After 24 hours, each press on the
buttonadd6hoursuntil48h.
tub.
3. Switch on the power and press the "Program" button to select the "Bulky" program and
2. Open the tap and hang the drain hose up.
3. Load laundry and put detergent.
4. Select the proper water level according to the
quantity of clothes.
Remaining time
"High" or "Medium" water level.
4. Press the "Start/Pause" button, and c lose the lid.
5. At the end of program,put the blanket on a clothes line. Make sure the blanket is flat and
(Minutes)
free of wrinkle.
5. Select the functions and programs.
6. Press "Delay button to select the beginning time of
washing.
Delay (hour)
Notices:
Delay
7. Press "Start/Pause" button and close the lid.
Confirmation of the delay and inspection
After the delay function is started, the corresponding light will be turned on, and other lights
are turned off.
Fold three times in the
same direction
Put it into the wash tub with
the edge downwards
Fold in two by the long side
Roll up the blanket.
Use the detergent twice
After the delay function is started, press "Delay" button continuously, you may see the selected
programs and the rest of the delay time. Loosen the button, the program will automatically
come back to delay status.
1. Put some laundry and detergent in the washing tub, press "Function" button and set the
"Single wash" program then make the washing machine into operation..
2. Take out the laundry after hearing the buzzing sound.
3. Put the second batch of laundry in the washing tub and let the washing machine finish
the whole washing program.
4. Take out the second batch of laundry after hearing the buzzing sound.
5. Put the first batch laundry in the washing tub. Power on and chose wash-spin functions.
Let the washing machine finish the whole program.
Cancel the delay time, or alter the delay time
Before the program is started , the delay indicator lights, the delay time is selected from 1 to
48 hours,afer the delay time is set over 48 hours, the delay indicator is turned off , the
function will be cancelled.
Press power switch to end program, and to cancel delay time at the same time.
To change the delay time, please press "Start/Pause", and then press "Delay" button to reset.
Load size and detergent
Water
level
Water
volume
Weight of
washing
Washing powder
Pre-wash of the dirty clothes
As for seriously stained dirty clothes with mud, one of the "Rinse-spin" program can be selected to
perform pre-washing, and then add washing powder and select the fully automatic program to
wash them. You can use the hot water for wash.
About 70g
About 66g
About 60g
About 52g
About 44g
About 36g
About 28g
About 20g
About 53L
About 48L
8
7
6
5
About 43L
About 38L
About 34L
About 30L
About 25L
About 17L
Washing tips
Checking pocket of clothes to avoid coins, clips and etc..
Reversing the clothes which is easy teaseled.
4
3
To resist clothes`s crossing, please cross their sleeves or the ties in advance.
Before washing , remove from clothes`s bedload.
Zipping the clothes if they have in advance.
2
1
<0.8kg
Separating clothes if they have easily fading color.
To put clothes of puff and into washing net bag.
Notices:
For special dirty part of clothes you may use some detergent.
The highest priority of using the detergent is low and mid foam detergent.
The volume of detergent is changed with different type. You need to read the user manual.
Wash of blanket
The weight of blanket should be less than 4kg, and please select the bulky program for
Water volume is different because of clothes variety. When the washing machine runsnot
well, please adjust clothes volume andwater level.
washing.
The water volume above listed isbased on normal clothes volume.
14
13
WAY OF USE & METHOD OF MAINTENANCE
TROUBLE SHOOTING
Exceptional
Cause
phenomenon
Weight standard of the clothes
Solution
Re-plug the power plug.
Check the power socket, or change other
socket.
The power plug is not plugged tight.
The power switch is not switched
on.
No indication
in controller
Press "START/PAUSE" button.
Not press "START/PAUSE" button.
Bedsheet (cotton)
about 500g
Long sleeves shirt
(blended) about 200g
A pair of pajamas
(cotton) about 500g
A suit of work clothes
(blended) about 800g
Do not rightly connect the tap with
the universal connector.
Re-install rightly the universal connector.
Screw tight the nut.
The inlet hose
.leakage
Do not screw tight the nut of the
water inlet hose.
Socks (blended)
about 50g
Short sleeves shirt
(cotton) about 130g
Bath towel (cotton)
about 300g
Short pants (cotton)
about 50g
The drain hose is wrung or jammed.
Loosen the drain hose for smooth flow
of water
Does not drain
Method Of Maintenance
Wait for coming water.
Stop water.
The following cases are not faults
1.There is water injection in time of washing or rinse, which is due to that the washer senses the inadequacy of water
Open the tap.
Do not open the tap.
Dose not inject water
Clean the netting according to the method of
"Cleaning of the water inlet".
Whether the wire netting in the water
inlet was stopped up by the sundries.
and exchanges water level automatically.
2.There is the phenomenon of intermittent spinning in the beginning of spinning, which is performed to achieve better
spinning effects.
3. In the course of spin, the program return to the wash program. Because that is designed to rectify the unbalanced
This is automatic rectification for spinning
in the washing program. That the washing
are too much or too little, or that the
washing machine is not placed plane will
cause the unbalance in time of spinning. If
there is still abnormal circumstances after
checking the above-mentioned points,
please pull out the power plug and contact
withlocalserviceassoonaspossible.
distribution of load in the spin tub.
Spinning stops and
water injecting begains
in the course of spin
Cause by that the washing
placed uneven.
Maintenance of shell
Use soft cloth to wipe off the
water and dirt on the surface
each time after use of the
washing machine. Detergent,
propellant and other chemicals
are not allowed to use, for they
can cause damage to the
surface.
After the whole washing program
The washing machine will send off the "DOU-
DOU"sound after any program operation to
remind you of taking out the load or going on
with other operations.
After end to drain, do not close the lid.
Open the lid in course of spinning.
Does not spin
Close the upper lid.
After finishing washing, please shut off the tap,
pull out the plug in case of water leakage or fire
accident.
In order to attain the better spinning
effect.
Belong to thenormal
phenomenon generally.
Intermittent spinning
Cleaning the water inlet
Cleaning of the lint filter
Before using the machine
water exsits
After long time use, the water inlet mesh bag may
be blocked with smudginess, and should be
cleaned according to the following steps:
After using the washing machine for a period, please
clean it according to the following steps:
Remainning water due to testing
or experiment in the factory.
Belong to thenormal
phenomenon generally.
in the drain hose.
1. Switch on the power, followed by shutting off the 1. Take out the lint filter.
tap .
2. Open the lint filter and wash it clean in the water.
3. Restore it and refix it.
2. Let the washer works for 5 seconds so that water
flows into the tub through the water inlet hose. then
turn off the power.
Notices:
The washing machine does not work normally because the voltage is low or too high. Please pull
out the plug and wait till the voltage becomes normal.
3. Unload the water inlet hose and clean the mesh
bag, then restore the water inlet assembly.
If there is still abnormal circumstances after checking the above-mentioned points, please pull out
the plug. Do not repair it by yourself at home, which is very dangerous.
16
15
PRECAUTIONS
OTHER FUNCTIONS
Function of fault alarm
Safe use of power
Keep away from dampness
Alarm of the
buzzing sound
Don't place the washing machine in extreme
damp surroudings, for dampness may weaken
the insulation of the machine, which may cause
electric shock or faults.
Please plug the power cord into the special
voltage. The plug-in and plug-out of the wire
should go on with the plug held with hand.
Indication of fault
Cause of fault
Solution of alarm
Phenomenon of fault
Open the lid to
deal with faults,
then close the
lid to solve the
alarm.
The buzzer
goes on
Entering water less than
16 minutes, reset water
Alarm for
water injection
E1
buzzing sound
for 10 seconds.
If the alarm
does not be
solved , every
16 minutes re-
buzzs for 10
seconds.
Open the lid after start the
delay time. Open the lid
when the washer is
Alarm for
opening lid
E2
Be examined imbalance
for the third time.
Imbalance alarm
Drain alarm
E3
E4
After draining for 4
minutes, does not
Don't open the lid in time of spinning
Don't use hot water
If the lid is opened in time of spinning, the washing
machine will arrest at once, which will shorten the
service life. Please avoid opening the lid in the
course of operation as possible
and furthermore, don't
Don't use hot water over 50
deformation of the plastics.
to avoid
put hands into the tub,
for it is very dangerous
that the clothes wind
the hand despite of low
Function of automatic power-off
speed of rotation.
1. Start 10 minutes later to not work, automatically shut off the power.
2. After end to wash and the buzzer sounds 6 times, the washing machine will
automatically shut off..
Avoid spray of water
Keep away from smoke and fire
Function of adjusting for unbalance
Don't place lighted candles, cigarettes and thermos
nearby to avoid fire accidents or deformation of the
plastics.
Don't let water spray onto the switch or the
control panel in case of electric shock and
faults.
1. If the clothes are placed uneven before spinning, easy to result in bigger vibrancy of spinning.
The washing machine has a function of adjusting unbalance. When working, the system of the
washing machine always inspects running state. If finding a phenomenon that the spinning vibrancy
is too big, the washing machine automatically start the adjusting program To adjust the clothes`s
state.
2. Thewashingmachinecanadjustunbalancetwice, ifnoeffect, itwillalarm.
18
17
Dimension
32 kg
6.0Kg (Dry clothes)
0.6Mpa
526X536X927 mm
360 W
Weight of the product
Rated volume of wash
and spinning
Rated input
power
Maximum water pressure
permitted in the water inlet
230 V
Rated voltage
Minimum water pressure
permitted in the water inlet
Rated frequency
50Hz
0.1Mpa
|