Hotpoint Washer Dryer WDPG 9640 User Manual

Instructions for use  
WASHER-DRYER  
!
This symbol reminds you to read this instruction manual.  
GB  
Contents  
GB  
English,1  
Installation, 2-3-4-5  
Unpacking and levelling  
Connecting the electricity and water supplies  
The first wash cycle  
Technical data  
Care and maintenance, 6  
Cutting off the water and electricity supplies  
Cleaning the washer-dryer  
Cleaning the detergent dispenser drawer  
Caring for the door and drum of your appliance  
Cleaning the pump  
Checking the water inlet hose  
Precautions and advice, 7  
General safety  
Disposal  
WDPG 9640  
Opening the porthole door manually  
Description of the washer-dryer, 8-9  
Control panel  
Display  
How to run a wash cycle or a drying cycle, 10  
Wash cycles and options, 11  
Table of wash cycles  
Wash options  
Detergents and laundry, 12  
Detergent dispenser drawer  
Preparing the laundry  
Special wash cycles  
Troubleshooting, 13-14  
Assistance, 15-16  
1
 
Connecting the drain hose  
• the supply voltage is included within the  
values indicated on the Technical Data Plate  
fixed on the machine.  
GB  
Connect the drain  
hose, without bending  
it, to a draining  
• the socket is compatible with the washer-  
dryers plug. If this is not the case, replace  
the socket or the plug.  
duct or a wall drain  
situated between 65  
and 100 cm from the  
floor;  
65 - 100 cm  
Your appliance is now supplied with a 13 amp  
fused plug it can be plugged into a 13 amp  
socket for immediate use. Before using the  
appliance please read the instructions below.  
WARNING - THIS APPLIANCE MUST BE  
EARTHED.  
The drain hose may  
be connected to  
an under-sink trap.  
Before connecting  
the drain hose from  
the machine ensure  
that any blanks or  
removable ends have  
been taken off the  
spigot.  
THE FOLLOWING OPERATIONS SHOULD  
BE CARRIED OUT BY A QUALIFIED  
ELECTRICIAN.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be  
used, and the fuse cover re-fitted. If the fuse  
cover is lost, the plug must not be used until a  
replacement is obtained.  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must  
be of the correct colour as indicated by  
the coloured marking or the colour that is  
embossed in words on the base of the plug.  
Replacements can be obtained directly from  
your nearest Service Depot.  
If it is placed over  
the edge of a basin  
or sink be sure  
the free end of the  
hose should not be  
underwater.  
Removing the plug:  
If your appliance has a non-rewireable  
moulded plug and you should wish to re-route  
the mains cable through partitions, units etc.,  
please ensure that either:  
the plug is replaced by a fused 13 ampere  
rewireable plug bearing the BSI mark of  
approval.  
! We advise against the use of hose extensions;  
in case of absolute need, the extension must  
have the same diameter as the original hose  
and must not exceed 150 cm in length.  
Ensure that if the drain hose is pushed into  
a standpipe, that the end does not go down  
more than 15cms (6 inches). If the hose is  
pushed down too far, this may cause the  
machine to self -syphon ie. continuously empty  
as it is filling.  
or:  
the mains cable is wired directly into a 13  
amp cable outlet, controlled by a switch, (in  
compliance with BS 5733) which is accessible  
without moving the appliance.  
Disposing of the plug:  
Ensure that before disposing of the plug itself,  
you make the pins unusable so that it cannot  
be accidentally inserted into a socket.  
Electric connection  
Instructions for connecting cable to an alternative  
Before plugging the appliance into the mains  
socket, make sure that:  
plug:  
Important: the wires in the mains lead are  
coloured in accordance with the following  
code:  
the socket is earthed and in compliance with  
the applicable law;  
Green & Yellow Earth  
the socket is able to sustain the appliances  
maximum power load indicated on the  
Technical Data Plate fixed on the machine;  
Blue  
Brown  
Neutral  
Live  
3
 
As the colours of the wires in the lead may  
not correspond with the coloured markings  
identifying the terminals in your plug, proceed  
as follows:  
! The power supply cable must only be  
GB  
replaced by an authorised serviceman.  
Warning! The company denies all liability if and  
when these norms are not respected.  
Connect Green & Yellow wire to terminal  
marked E or or coloured Green or Green &  
Yellow.  
The first wash cycle  
Connect Brown wire to terminal marked L or  
coloured Red.  
Once the appliance has been installed, and  
before you use it for the first time, run a wash  
cycle with detergent and no laundry, using the  
programme “Auto Clean” (see “Cleaning the  
washer-dryer”).  
Connect Blue wire to terminal marked N or  
coloured Black.  
If a 13 amp plug (BS 1363) is used it must be  
fitted with a  
13 amp fuse, either in the plug or adaptor or  
at the distribution board.  
If you are in any doubt regarding the electrical  
supply to your machine, consult a qualified  
electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
BLUE  
NEUTRAL (N)  
LIVE (L)  
EARTH (E)  
BROWN  
GREEN & YELLOW  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
CROSS-BAR  
CORD GRIP  
BLUE  
Disposing of the appliance:  
When disposing of the appliance please  
remove the plug by cutting the mains cable  
as close as possible to the plug body and  
dispose of it as described on the previous  
page.  
! The washer-dryer should not be installed  
in an outdoor environment, not even where  
the area is sheltered, because it may be very  
dangerous to leave it exposed to damp, rain  
and thunderstorms.  
! When the washer-dryer is installed, the mains  
socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent  
or dangerously compressed.  
4
 
Technical data  
GB  
Model  
WDPG 9640  
width 59.5 cm  
Dimensions height 85 cm  
depth 60,5 cm  
from 1 to 9 kg for the wash  
programme  
Capacity  
Electrical  
from 1 to 6 kg for the drying  
programme  
please refer to the technical  
connections data plate fixed to the machine  
maximum pressure  
1 MPa (10 bar)  
Water con-  
minimum pressure  
nections  
0.05 MPa (0.5 bar)  
drum capacity 62 litres  
up to 1400 rotations per  
minute  
Spin speed  
Wash: programme 4; tem-  
perature 60°C; using a load  
of 9 kg.  
Energy ra-  
ted  
Drying: the smaller load  
must be dried by selecting  
programmes the “A4” (EXTRA) dryness le-  
according to vel. The load must consist of  
regulation  
EN 50229  
3 sheets, 2 pillowcases and  
1 hand towel; the remainder  
of the load must be dried by  
selecting the “A4” (EXTRA)  
dryness level.  
This appliance conforms to  
the following EC Directives:  
- 2004/108/EC (Electromagne-  
tic Compatibility)  
- 2006/95/EC (Low Voltage)  
- 2002/96/EC  
5
 
Care and maintenance  
Cutting off the water and  
electricity supplies  
Cleaning the pump  
GB  
The washer-dryer is fitted with a self-cleaning  
pump which does not require any maintenance.  
Sometimes, small items (such as coins or  
buttons) may fall into the pre-chamber which  
protects the pump, situated in its bottom part.  
• Turn off the water tap after every wash cycle.  
This will limit wear on the hydraulic system  
inside the washer-dryer and help to prevent  
leaks.  
• Unplug the washer-dryer when cleaning it  
and during all maintenance work.  
! Make sure the wash cycle has finished and  
unplug the appliance.  
Cleaning the washer-dryer  
To access the pre-chamber:  
• The outer parts and rubber components  
of the appliance can be cleaned using a soft  
cloth soaked in lukewarm soapy water. Do not  
use solvents or abrasives.  
• The washer-dryer has a “Auto Clean”  
programme for its internal parts that must be  
run with no load in the drum.  
1. using a  
screwdriver, remove  
the cover panel on  
the lower front part of  
the washer-dryer (see  
figure);  
To help the wash cycle you may want to use  
either the detergent (i.e. a quantity 10% the  
quantity specified for lightly-soiled garments)  
or special additives to clean the washer-  
dryer. We recommend running a cleaning  
programme every 40 wash cycles.  
2. unscrew the lid  
by rotating it anti-  
clockwise (see figure):  
a little water may  
trickle out. This is  
perfectly normal;  
To start the programme  
A
press button A for 5  
seconds (see figure).  
The programme will  
start automatically and  
will run for about 70  
minutes. To stop the  
cycle press the START/  
PAUSE button.  
3. clean the inside thoroughly;  
4. screw the lid back on;  
Cleaning the detergent dispenser  
drawer  
5. reposition the panel, making sure the hooks  
are securely in place before you push it onto  
the appliance.  
Remove the  
1
dispenser by raising it  
and pulling it out (see  
figure).  
Checking the water inlet hose  
Wash it under running  
water; this operation  
should be repeated  
Check the inlet hose at least once a year. If  
there are any cracks, it should be replaced  
immediately: during the wash cycles, water  
pressure is very strong and a cracked hose  
could easily split open.  
frequently.  
2
! Never use second-hand hoses.  
Caring for the door and drum of  
your appliance  
• Always leave the porthole door ajar in order  
to prevent unpleasant odours from forming.  
6
 
Precautions and tips  
! This washer-dryer was designed and constructed in  
accordance with international safety regulations. The  
following information is provided for safety reasons and  
must therefore be read carefully.  
Disposal  
GB  
Disposing of the packaging materials: observe local  
regulations so that the packaging may be re-used.  
The European Directive 2002/96/EC on Waste Electrical  
and Electronic Equipment, requires that old household  
electrical appliances must not be disposed of in the  
normal unsorted municipal waste stream. Old appliances  
must be collected separately in order to optimise the  
recovery and recycling of the materials they contain and  
reduce the impact on human health and the environment.  
The crossed out “wheeled bin” symbol on the product  
reminds you of your obligation, that when you dispose of  
the appliance it must be separately collected. Consumers  
should contact their local authority or retailer for information  
concerning the correct disposal of their old appliance.  
General safety  
• This appliance is not intended for use by persons  
(including children) with reduced physical, sensory  
or mental capabilities, or lack of experience and  
knowledge, unless they have been given supervision or  
instruction concerning use of the appliance by a person  
responsible for their safety.  
Children should be supervised to ensure that they do  
not play with the appliance.  
– Do not dry unwashed items in the tumble dryer.  
– Items that have been soiled with substances such  
as cooking oil, acetone, alcohol, petrol, kerosene,  
spot removers, turpentine, waxes and wax removers  
should be washed in hot water with an extra amount of  
detergent before being dried in the tumble dryer.  
– Items such as foam rubber (latex foam), shower caps,  
waterproof textiles, rubber backed articles and clothes  
or pillows fitted with foam rubber pads should not be  
dried in the tumble dryer.  
– Fabric softeners, or similar products, should be used  
as specified by the fabric softener instructions.  
– The final part of a tumble dryer cycle occurs without  
heat (cool down cycle) to ensure that the items are left  
at a temperature that ensures that the items will not be  
damaged.  
Opening the porthole door manually  
In the event that it is not possible to open the porthole  
door due to a powercut, and if you wish to remove the  
laundry, proceed as follows:  
1. remove the plug from the  
electrical socket.  
2. make sure the water level  
inside the machine is lower  
than the door opening; if  
it is not, remove excess  
water using the drain hose,  
collecting it in a bucket as  
indicated in the figure.  
WARNING: Never stop a tumble dryer before the end  
of the drying cycle unless all items are quickly removed  
and spread out so that the heat is dissipated.  
• This appliance was designed for domestic use only.  
• Do not touch the machine when barefoot or with wet or  
damp hands or feet.  
• Do not pull on the power supply cable when unplugging  
the appliance from the electricity socket. Hold the plug  
and pull.  
3. using a screwdriver,  
remove the cover panel on  
the lower front part of the  
washer-dryer (see figure).  
• Do not touch the drained water as it may reach  
extremely high temperatures.  
• Never force the porthole door. This could damage the safety  
lock mechanism designed to prevent accidental opening.  
• If the appliance breaks down, do not under any  
circumstances access the internal mechanisms in an  
attempt to repair it yourself.  
• Always keep children well away from the appliance while  
it is operating.  
• If it must be moved, proceed with the help of two or  
three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
• Before loading laundry into the washer dryer, make sure  
the drum is empty.  
• During the drying phase, the door tends to get quite hot.  
• Do not use the appliance to dry clothes that have  
been washed with flammable solvents (e.g.  
trichlorethylene).  
• Do not use the appliance to dry foam rubber or  
similar elastomers.  
4. pull outwards using the tab as indicated in the figure,  
until the plastic tie-rod is freed from its stop position; pull  
downwards and open the door at the same time.  
5. reposition the panel, making sure the hooks are securely  
in place before you push it onto the appliance.  
• Make sure that the water tap is turned on during  
the drying cycles.  
7
 
Description of the washer-dryer  
Control panel  
GB  
TEMPERATURE  
CLEANING  
ACTION  
button  
button  
CHILD  
LOCK  
button  
ON/OFF  
button  
DISPLAY  
START/PAUSE  
button and indicator  
light  
SPIN  
WASH  
Detergent dispenser drawer  
button  
CYCLE  
OPTION  
SELECTOR  
KNOB  
buttons and  
indicator lights  
DRY  
button  
Detergent dispenser drawer: used to dispense  
detergents and washing additives (see “Detergents and  
laundry”).  
DRY button  
: press to decrease or exclude drying; the  
selected drying level or time will appear on the display.  
START/PAUSE button and indicator light: when the green  
indicator light flashes slowly, press the button to start a  
wash cycle. Once the cycle has begun the indicator light  
will remain lit in a fixed manner. To pause the wash cycle,  
press the button again; the indicator light will flash in an  
amber colour. If the  
may be opened. To start the wash cycle from the point at  
which it was interrupted, press the button again.  
ON/OFF  
button: press this briefly to switch the  
machine on or off. The START/PAUSE indicator light which  
flashes slowly in a green colour shows that the machine  
is switched on. To switch off the washer-dryer during the  
wash cycle, press and hold the button for approximately 3  
seconds; if the button is pressed briefly or accidentally the  
machine will not switch off.  
symbol is not illuminated, the door  
If the machine is switched off during a wash cycle, this  
wash cycle will be cancelled.  
CHILD LOCK button  
lock, press and hold the button for approximately 2  
seconds. When the symbol is illuminated, the control  
panel is locked (apart from the ON/OFF button). This  
means it is possible to prevent wash cycles from being  
modified accidentally, especially where there are children in  
the home. To deactivate the control panel lock, press and  
hold the button for approximately 2 seconds.  
: to activate the control panel  
WASH CYCLE SELECTOR KNOB: used to set the  
desired wash cycle (see “Table of programmes and wash  
cycles”).  
OPTION buttons and indicator lights: press to select the  
available options. The indicator light corresponding to the  
selected option will remain lit.  
Standby mode  
This washer-dryer, in compliance with new energy saving  
regulations, is fitted with an automatic standby system  
which is enabled after about 30 minutes if no activity is  
detected. Press the ON-OFF button briefly and wait for the  
machine to start up again.  
CLEANING ACTION button  
wash intensity.  
: to select the desired  
TEMPERATURE  
button: press to reduce or  
completely exclude the temperature; the value appears on  
the display.  
Consumption in off-mode: 0.5 W  
Consumption in Left-on: 0.5 W  
SPIN  
button: press to reduce or completely exclude  
the spin cycle; the value appears on the display.  
8
 
Display  
GB  
B
A
C
The display is useful when programming the machine and provides a great deal of information.  
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED  
START option has been set, the countdown to the start of the selected wash cycle will appear.  
Moreover, pressing the relative button allows for visualising the maximum values for the temperature, spin speed or type of  
drying relative to the selected programme or the most recently selected ones, if compatible with the selected programme.  
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle  
appear in section B:  
Main wash  
Rinse  
Spin/Pump out  
Drying  
The icons corresponding to “temperature”, “spin” and “drying” (working from the left) are displayed in section C.  
The “temperature” bars  
The “spin” bars  
indicate the maximum temperature level which may be selected for the set cycle.  
indicate the maximum spin level which may be selected for the set cycle.  
The  
symbol lights up while the drying settings are being adjusted.  
DOOR LOCKED  
indicator light:  
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door.  
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED  
off the door may be opened.  
symbol is switched  
9
 
How to run a wash cycle or a  
drying cycle  
Selecting the cotton drying cycle through the programme  
selector knob and pressing the “Eco” button activates an  
automatic drying cycle that allows for saving energy, thanks  
to an optimal combination of air temperature and cycle  
duration; the display will visualise the “A2” dryness level.  
1. SWITCH THE MACHINE ON. Press the  
button; the  
GB  
START/PAUSE indicator light will flash slowly in a green  
colour.  
2. LOAD THE LAUNDRY. Open the porthole door. Load  
the laundry, making sure you do not exceed the maximum  
load value indicated in the table of programmes and wash  
cycles on the following page.  
Set the desired wash intensity.  
Option  
makes it possible to optimise washing based  
on the level of soil in the fabrics and on desired wash cycle  
intensity.  
Select the wash programme: the cycle will be automatically  
set to “Normal” as optimised for garments with an average  
level of soil (this setting is not applicable to the “Wool”  
cycle, which is automatically set to “Delicate”).  
3. MEASURE OUT THE DETERGENT. Pull out the  
detergent dispenser drawer and pour the detergent into  
the relevant compartments as described in “Detergents  
and laundry”.  
4. CLOSE THE DOOR.  
For heavily-soiled garments press  
button until the  
5. SELECT THE WASH CYCLE. Use the WASH CYCLE  
SELECTOR knob to select the desired wash cycle. A  
temperature and spin speed is set for each wash cycle;  
these values may be adjusted. The duration of the cycle will  
appear on the display.  
Intensive” level is reached. This level ensures a high-  
performance wash due to a larger quantity of water used  
in the initial phase of the cycle and due to increased drum  
rotation. It is useful when removing the most stubborn  
stains.  
6. CUSTOMISE THE WASH CYCLE. Use the relevant buttons:  
For lightly-soiled garments or a more delicate treatment  
Modify the temperature and/or spin speed. The  
machine automatically displays the maximum temperature  
and spin speed values set for the selected cycle, or the  
most recently-used settings if they are compatible with  
the selected cycle. The temperature can be decreased by  
of the fabrics, press  
is reached. The cycle will reduce drum rotation to ensure  
washing results that are perfect for delicate garments.  
button until the “Delicate” level  
Modify the cycle settings.  
• Press the button to enable the option; the indicator light  
corresponding to the button will switch on.  
• Press the button again to disable the option; the  
indicator light will switch off.  
! If the selected option is not compatible with the set wash  
cycle, the indicator light will flash and the option will not be  
activated.  
! If the selected option is not compatible with a previously  
selected one, the indicator light corresponding to the first  
function selected will flash and only the second option will  
be activated; the indicator light for the option which has been  
activated will be illuminated.  
pressing the  
is reached. The spin speed may be progressively reduced  
by pressing the button, until it is completely excluded  
button, until the cold wash “OFF” setting  
(the “OFF” setting). If these buttons are pressed again, the  
maximum values are restored.  
Setting the drying cycle  
The first time the button  
is pressed, the machine will  
automatically select the maximum drying cycle which is  
compatible with the selected wash cycle. Subsequent  
presses will decrease the drying level and then the drying  
time, until the cycle is excluded completely (“OFF”).  
Drying may be set as follows:  
A- Based on the desired laundry dryness level:  
Iron “A1”: suitable for clothes which will need ironing  
afterwards. the remaining dampness softens creases,  
making them easier to remove.  
Hanger “A2”: ideal for clothes which do not need to be  
dried fully.  
Cupboard “A3”: suitable for laundry which can be put  
back in a cupboard without being ironed.  
Extra “A4”: suitable for garments which need to be dried  
completely, such as sponges and bathrobes.  
B - Based on a set time period: between 30 and 180  
minutes.  
If your laundry load to be washed and dried is much  
greater than the maximum stated load, perform the wash  
cycle, and when the cycle is complete, divide the garments  
into groups and put some of them back in the drum. At this  
point, follow the instructions provided for a “Drying only”  
cycle. Repeat this procedure for the remainder of the load.  
A cooling-down period is always added to the end of each  
drying cycle.  
! The options may affect the recommended load value and/  
or the duration of the cycle.  
7. START THE WASH CYCLE. Press the START/PAUSE  
button. The corresponding indicator light will turn green,  
remaining lit in a fixed manner, and the door will be locked (the  
DOOR LOCKED  
symbol will be lit). To change a wash  
cycle while it is in progress, pause the washer-dryer using the  
START/PAUSE button (the START/PAUSE indicator light will  
flash slowly in an amber colour); then select the desired cycle  
and press the START/PAUSE button again. To open the door  
while a cycle is in progress, press the START/PAUSE button; if  
the DOOR LOCKED  
be opened. Press the START/PAUSE button again to restart  
the wash cycle from the point at which it was interrupted.  
symbol is switched off the door may  
8. THE END OF THE WASH CYCLE. This will be indicated  
by the text “END” on the display; when the DOOR LOCKED  
symbol switches off the door may be opened. Open the  
door, unload the laundry and switch off the machine.  
! If you wish to cancel a cycle which has already begun, press  
and hold the  
button. The cycle will be stopped and the  
Drying only  
machine will switch off.  
Use the cycle selector knob to select a drying cycle (12-13-14)  
in accordance with the type of fabric. The desired drying level or  
time may also be set using the DRYING button  
.
10  
 
Wash cycles and options  
Table of wash cycles  
GB  
Detergents  
Fabric  
Max.  
Max.  
Max.  
load  
(kg)  
Cycle  
duration  
Description of the wash cycle  
temp. speed Drying  
(°C)  
(rpm)  
Wash  
softener  
CLEAN Plus  
1
2
3
4
5
6
6
Anti Stain  
40°  
60°  
90°  
60°  
40°  
60°  
40°  
1400  
1400  
1400  
1400  
1400  
800  
5
5
9
9
9
4
4
Whites  
Cottons: extremely soiled whites.  
Cottons (1): heavily soiled whites and resistant colours.  
Cottons (2): lightly soiled resistant colours.  
Synthetics: heavily soiled resistant colours.  
Synthetics (3): heavily soiled resistant colours.  
SPECIALS  
800  
7
8
9
Anti Allergy  
60°  
40°  
30°  
1400  
800  
0
5
2
1
Wool: for wool, cashmere, etc.  
Delicates  
Fastwash 30’: to refresh lightly soiled garments quickly (not suitable for wool,  
silk and clothes which require washing by hand).  
10  
30°  
30°  
800  
3,5  
1
11 Ready to Wear  
DRYING  
1400  
12 Drying Cottons  
-
-
-
-
-
-
-
-
-
-
-
-
6
4
2
13 Drying Synthetics  
14 Drying Wool  
Partials cycles  
Rinse  
-
-
1400  
1400  
-
-
9
9
Spin+Pump out  
-
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary  
according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options  
selected.  
For all Test Institutes:  
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 4 with a temperature of 60°C.  
2) Long wash cycle for cottons: set wash cycle 5 with a temperature of 40°C.  
3) Long wash cycle for synthetics: set wash cycle 6 with a temperature of 40°C.  
Wash options  
Delay Timer  
Eco  
To set a delayed start for the selected cycle, press the  
corresponding button repeatedly until the required delay  
period has been reached. When this option is enabled, the  
corresponding indicator light will remain lit. To remove the  
delayed start setting, press the button until the text “OFF”  
appears on the display.  
The Eco option saves energy by not heating the water  
used to wash your laundry – an advantage both to the  
environment and to your energy bill. Instead, intensified  
wash action and water optimisation ensure great wash  
results in the same average time of a standard cycle.  
For the best washing results we recommend the usage of  
a liquid detergent  
! This option can be used in conjunction with all cycles.  
! It cannot be used in conjunction with wash cycles 1, 2, 7,  
8, 9, 11, 13, 14,  
,
.
By selecting the drying function as well, an automatic  
drying cycle automatically activates at the end of the wash  
cycle – it too allows for saving energy, thanks to the optimal  
combination of air temperature and cycle duration.  
! It can be activated with programmes 3, 4 and 5.  
11  
 
Detergents and laundry  
from yellowing due to sunlight exposure and preventing loss  
Detergent dispenser drawer  
GB  
of whiteness caused by the possible presence of dust in the  
air. Drying cycles can only be selected on a level basis.  
Anti Allergy: use programme 7 to remove major allergens  
such as pollen, mites, cat’s and dog’s hair.  
Successful washing results also depend on the correct  
dose of detergent: adding too much detergent will not  
necessarily result in a more efficient wash, and may in  
fact cause build up on the inside of your appliance and  
contribute to environmental pollution.  
Wool: the wool wash cycle on this Hotpoint machine has  
been tested and approved by The Woolmark Company  
for washing wool garments labelled as hand washable  
provided that the garments are washed according to the  
instructions on the garment label and those issued by the  
manufacturer of this washer-dryer. Hotpoint is the first  
washer-dryer brand to be approved by The Woolmark  
Company for Apparel Care- Platinum for its washing  
performance and consumption of energy and water.  
(M1127)  
! Do not use hand washing detergents; they create too  
much foam.  
Open the detergent  
A
B
dispenser drawer and pour  
in the detergent or washing  
additive, as follows.  
!Do not pour detergent into  
the middle compartment (*).  
Detergent should only be  
*
1
2
In UK, Eire, Hong Kong and India the Woolmark trade mark  
is a Certification trade mark.  
poured into the compartment 1.  
Delicates: use programme 9 to wash very delicate  
garments with decorative features, such as diamantes and  
sequins.  
compartment 1: Detergent for the wash cycle  
(powder or liquid)  
If liquid detergent is used, it is recommended that the  
removable plastic partition A (supplied) be used for proper  
dosage.  
If powder detergent is used, place the partition into slot B.  
compartment 2: Additives (fabric softeners, etc.)  
The fabric softener should not overflow the grid.  
To wash silk garments and curtains select the cycle 9 and  
set the “Delicate” level from option  
.
We recommend turning the garments inside out before  
washing and placing small items into the special bag  
for washing delicates. Use liquid detergent on delicate  
garments for best results.  
When selecting an exclusively time-based drying function,  
a drying cycle is performed at the end of the wash cycle  
that is particularly delicate, thanks to light handling and  
appropriate temperature control of the water jet.  
The recommended durations are:  
Preparing the laundry  
• Divide the laundry according to:  
- the type of fabric/the symbol on the label  
1 kg of synthetic garments --> 150 min  
1 kg of synthetic and cotton garments --> 180 min  
1 kg of cotton garments --> 180 min  
The degree of dryness depends on the load and fabric  
composition.  
Ready to Wear: select programme 11 for washing and  
drying lightly soiled garments (Cotton and Synthetic) in a  
short time. This cycle may be used to wash and dry a  
laundry load of up to 1 kg in just 45 minutes.  
To achieve optimum results, use liquid detergent and pre-  
treat cuffs, collars and stains.  
- the colours: separate coloured garments from whites.  
• Empty all garment pockets and check the buttons.  
• Do not exceed the values listed in the Table of wash cycles”,  
which refer to the weight of the laundry when dry.  
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1,200 g  
1 towel 150-250 g  
Load balancing system  
Special wash cycles  
Before every spin cycle, to avoid excessive vibrations  
before every spin and to distribute the load in a uniform  
manner, the drum rotates continuously at a speed which  
is slightly greater than the washing rotation speed. If,  
after several attempts, the load is not balanced correctly,  
the machine spins at a reduced spin speed. If the load is  
excessively unbalanced, the washer-dryer performs the  
distribution process instead of spinning. To encourage  
improved load distribution and balance, we recommend  
small and large garments are mixed in the load.  
Anti Stain: the programme 1 is suitable to heavily-soiled  
garments with resistant colours. It ensures a washing class  
that is higher than the standard class (A class).  
When running the programme, do not mix garments of  
different colours. We recommend the use of powder  
detergent. Pre-treatment with special additives is  
recommended if there are obstinate stains.  
Whites: use this cycle 2 to wash white clothes. The  
programme is designed to maintain the brightness of white  
clothes over time. Use powder detergent for best results.  
If the drying function is selected, a drying cycle automatically  
activates at the end of the wash cycle that resembles open-  
air drying, with the added advantages of preserving garments  
12  
 
Troubleshooting  
Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make  
sure that the problem cannot be solved easily using the following list.  
GB  
Problem:  
The machine does not switch on.  
Possible causes / Solutions:  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
• A delayed start has been set.  
The machine does not fill with  
water or ‘H20’ flashes in the  
display.  
• The water inlet hose is kinked.  
• The water inlet hose is not connected to the water supply.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65  
water and continually drains away  
or Water left in the drum  
or Stuck on wash.  
and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to run  
into the machine, the drain hose must be positioned higher than the bottom of  
the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
The machine does not drain or spin • The Pump filter is blocked.  
- (error lights flashing).  
• The drain hose is kinked (see “Installation”).  
• New Installation - The blanking cap or spigot has not been removed if  
connected under a sink.  
• The drain hose or sink trap is blocked.  
The machine does spin.  
• The Spin Speed is set to “OFF”.  
The programme takes too long.  
• Programme times will vary due to water pressure, the incoming water  
temperature and if the wash load goes out of balance. This will increase the  
programme times accordingly (see ‘ The machine wont spin properly’ below).  
The Display sticks at one ‘time to  
end’ for more than 1 Minute or the  
Display changes the estimated ‘Time  
to End’ during the programme.  
• The display time is for guidance only - it is not a precise time to finish and  
may vary.  
The machine vibrates a lot during  
the spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
• New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• The load is in a slight out of balance condition and machine is spinning, but at  
a lower speed.  
• The appliance is not plugged into the socket, or not enough to make contact.  
• There has been a power failure.  
The washer-dryer does not dry.  
• The appliance door is not shut properly.  
• A DELAY TIMER has been set.  
• DRYING is in the OFF position.  
13  
 
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
GB  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the load  
required before the machine will go into higher spin speeds - This will increase  
the programme time accordingly. This is a safety feature to prevent damage.  
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,  
etc). - Try the programme again using a different load.  
The machine leaks from the  
dispenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the tap  
on the water supply pipe slightly and try again.  
• The machine is tilting forwards - It must be level when in its final position.  
The machine leaks (other than  
dispenser).  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill  
hose is missing the rubber washer.  
• The drain hose is not fixed in properly.  
The option lights and the START/  
PAUSE indicator light are flash  
rapidly and an error code appears  
on the display (eg F-01, F-..).  
• Switch off the machine and unplug it, wait for approximately 1 minute and then  
switch back on again. If the problem persists contact Technical Assistance  
Centre.  
The machine smells.  
• The machine requires a service wash. Run a 90 degree wash cycle with  
detergent and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly after  
the program has finished.  
• If there is no power to the machine you need to perform the manual unlocking  
procedure.  
Door Seal damaged at the bottom.  
• The door seal has drainage holes at the bottom - This is normal.  
• The water level is correct if it can be seen at the bottom of the door.  
The water level is too low when  
the machine is washing.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washer-dryers’ or ‘hand and machine wash’ or the like).  
Too much detergent was used - less detergent is required in soft water.  
After completing the programme,  
or before starting a programme,  
the machine has turned itself off  
(no lights).  
To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate  
the machine, it can then either be switched off or a new programme selected.  
General.  
Your washer-dryer contains sensors that monitor progress during the wash cycle  
(eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).  
Normally, if your machine successfully completes the cycle, there is unlikely to  
be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label, or wash items that are not intended as machine  
washable.  
14  
 
Assistance  
Guarantee  
12 Months Parts and Labour Guarantee  
GB  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs  
for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of  
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost  
to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will  
be a charge for our engineers time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair  
bills for the life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where  
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will replace your  
machine or, if you prefer, give you your money back.  
15  
 
195105690.01  
09/2012  
-
Xerox Fabriano  
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its working  
life than us - the manufacturer.  
GB  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000  
fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee  
you must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoints continued commitment to helping the environment, Hotpoint reserves the right to use  
quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove  
the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to  
ensure that the appliance can no longer be plugged into a mains socket, and the door  
16  
 

Graco Inc Paint Sprayer 12004 User Manual
Grizzly Lathe T25920 User Manual
Haier Dehumidifier DE45EM User Manual
Harbor Freight Tools Vacuum Cleaner 3394 User Manual
Harman Stove Company Electric Heater 1 90 797000 User Manual
Heat Controller Air Conditioner RAD 123H User Manual
Honeywell Thermostat CT30 User Manual
HP Hewlett Packard Computer Hardware ML110 G5 User Manual
HP Hewlett Packard Network Card 3C509B TP User Manual
Huffy Fitness Equipment M7800041 User Manual