Hotpoint Oven SE103PGX User Manual

Operating Instructions

OVEN

Contents

Installation, 2

Positioning

Electrical connection, 3

Data plate

English,1

Description of the appliance, 4

Overall view

Control panel

Start-up and use, 5

Control panel lock

DEMO mode

Setting the clock

Setting the timer

Starting the oven

SE103PGX

SQ103PGI

Cooking modes, 6-9

Manual cooking modes

Automatic cooking modes

Programming cooking

Practical cooking advice

Cooking advice table

Precautions and tips, 10

General safety

Disposal

Respecting and conserving the environment

Care and maintenance, 11-12

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Automatic cleaning with the "AST CLEAN function

After Sales Service, 13

Repair Service and Information Desk

Extended Warranties

Genuine Parts and Accessories

Guarantee, 14

Electrical Connection

Electrical connection

Power cable supply connection to the electrical

mains:

The electrical connection to the mains must be made

on the appliance. The power voltage and frequency

are as indicated on the rating plate.

We recommend you use a power supply cable which

is long enough to allow you to take the oven out of

its recess in the event of maintenance operations

(only use HAR - H 05 - RR" quality cables fitted with

a plug conforming to the regulations in force.

The plug must be accessible at all times.

! THIS APPLIANCE MUST BE EARTHED.

Connecting the power supply cable

Unplug the appliance before all operations, even

when replacing the oven lamp.

To open the terminal board:

• Using a screwdriver, press on the tabs situated

on each side of the terminal board cover.

Using the appliance without correct earthing is

highly dangerous.

• Pull open the terminal board cover.

! After connecting the appliance to the flexible

cable, tighten all the screws on the terminal

board.

To connect the power supply cable, proceed as

follows:

• Unscrew the cable clamp screw and the contact

screws L-N-6.

• "asten the wires beneath the screwheads using

the following colour scheme: Blue (N) Brown (L)

Yellow-Green 6

TABLE Oꢀ CHARACTERISTICS

width 43.5 cm

height 32 cm

depth 40 cm

Dimensions

Volume

• "asten the power supply cable in the

corresponding cable clamp and close the cover.

56 l

voltage: 220-240V ~ 50/60Hz

maximum power absorbed

2800 W

Electrical

connections

Electrical Connection:

Voltage "requency: 230

V-1+N 50Hz

"use Section: 16A

Directive 2002/40/EC on the

label of electric ovens.

Regulation EN 50304

Supply cable:

3x1.5mm²

ENERGY LABEL

Declared energy

consumption for 'orced

convection Class

– heating mode:

Gratin

This appliance conforms to

the following European

Economic Community

directives: 2006/95/EEC

dated 12/12/06 (Low

Voltage) and subsequent

amendments - 89/336/EEC

dated 03/05/89

You can connect your oven to the system means of

a terminal board. Refer to above information for the

minimal cable sections and the calibration of the

protective elements according to the connection.

If the appliance is installed with a junction box, an

omnipolar circuit breaker - with a minimum contact

opening of 3mm - should be installed between the

appliance and the mains.

(Electromagnetic

Compatibility) and

subsequent amendments -

93/68/EEC dated 22/07/93

and subsequent

amendments.

2002/96/EEC

Description

of the appliance

Overall view

GUIDES for the

sliding racks

Control panel

position 5

position 4

position 3

position 2

position 1

GRILL

DRIPPING PAN

Control panel

DURATION

icon

CONTROL PANEL

MANUAL

COOKING END TIME

icon

POWER

button

COOKING MODE

icons

START

DOOR LOCK

indicator

TIME

display

TEMPERATURE

display

STOP

CLOCK

icon

AUTOMATIC

COOKING

MODE

FAST CLEAN

selector

icons

TIMER

icon

TIME/TEMPERATURE

ADJUSTMENT

buttons

Start-up and use

! The first time you use your appliance, heat the empty

oven with its door closed at its maximum temperature

for at least half an hour. Ensure that the room is well

ventilated before switching the oven off and opening

the oven door. The appliance may emit a slightly

unpleasant odour caused by protective substances

used during the manufacturing process burning away.

! The timer does not switch the oven on or off.

Starting the oven

1. Switch the control panel on by pressing the

button.

2. Press the button corresponding to the desired

cooking mode. The TEMPERATURE display shows the

temperature of the cooking mode; the TIME display

shows the current time.

! The “Control panel lock” and “DEMO mode” can be

activated/deactivated even when the control panel is

switched off.

3. Press the "START" button to begin cooking.

4. The oven will begin its preheating phase, the current

temperature indicators will light up as the temperature

rises. The temperature may be adjusted by pressing

the "+" and "-" buttons.

Control panel lock

To lock the oven controls, press the

and

buttons simultaneously. A buzzer will sound and the

TEMPERATURE display shows "Loc".

Press again to unlock the controls. The "STOP" button

is always active.

5. When preheating is finished, a buzzer will sound

and all current temperature indicators will be turned on:

the food can then be placed in the oven.

6. During cooking it is always possible to:

- adjust the temperature by pressing the "+" and "-"

buttons;

Demo mode

The oven can operate in the DEMO mode: all heating

elements are deactivated, and the controls remain

operative.

- set the duration of a cooking mode (see Cooking

Modes);

- interrupt cooking by pressing the "STOP" button.

7. In case of a blackout, an automatic system will

reactivate the cooking mode from where it was

interrupted, provided the oven temperature has not

dropped below a certain level. Programmed cooking

modes which have not started will not be restored and

must be reprogrammed.

To activate the DEMO mode, press the "+",

, and

"START" buttons simultaneously. A buzzer will

sound and the TIME display shows "DEMO".

To activate the DEMO mode, press the "+" and

"START" buttons simultaneously. A buzzer will

sound and the "DEMO" message disappears from

the display.

! There is no preheating stage for the BARBECUE

mode.

Setting the clock and timer

After connection to the power supply network or after a

! Never put objects directly on the bottom of the oven;

this will avoid the enamel coating being damaged.

! Always place cookware on the rack(s) provided.

blackout, the

button and the digits on the TIME

display will flash.

To set the time:

1. Press buttons "+" and "-"; press and hold to scroll

the numbers quicker and make setting easier.

2. Once the exact time is reached, wait 10 seconds for

Cooling ventilation

In order to cool down the external temperature of the

oven, a cooling fan generates a stream of air which

escapes between the oven control panel and the oven

door. At the beginning of the "AST CLEAN mode, the

cooling fan operates at low speed.

the selection to be memorized, or press the

again to fix the setting.

button

! Once the cooking has been completed, the cooling

fan continues to operate until the oven has cooled

down sufficiently.

To make any necessary changes, switch off the control

panel by pressing the ; button, then press the

button and follow the steps indicated.

When the set time has elapsed, the timer emits a

buzzer that will automatically stop after 6 seconds or

when any active icon on the control panel is pressed.

Oven light

When the oven is not in operation, the lamp can be

switched on at any time by opening the oven door.

To set the timer, press the

button and follow the

procedure used to set the clock. The

button

switched on indicates that the timer has been

activated.

Cooking modes

Manual cooking modes

Spit roast (only available in certain models)

To operate the rotisserie

spit (see diagram)

! All cooking modes have a default cooking

temperature which may be adjusted manually

between 40°C and 250°C as desired.

proceed as follows:

In the BARBECUE mode, the default power level

value is indicated as a percentage (%) and may also

be adjusted manually.

MULTILEVEL mode

All heating elements and the fan are activated. Since the

heat remains constant throughout the oven, the air cooks

and browns food in a uniform manner. A maximum of two

racks may be used at the same time.

1. Place the dripping pan in position 1.

2. Place the rotisserie support in position 3 and

insert the spit into the hole provided on the back

panel of the oven.

BARBECUE mode

The top heating element and the rotisserie spit (where

present) are activated. By pressing the “+” and “-”

buttons on the left hand side of the control panel,

the power levels that may be set will appear on the

TEMPERATURE display; these range between 5%

and 100%. The high and direct temperature of the grill is

recommended for food which requires a high surface

temperature. Always cook in this mode with the oven door

closed.

3. Start the spit roast function by selecting the

modes.

! When the

mode is activated, the rotisserie spit

will stop if the door is opened.

Automatic cooking modes

! The temperature and cooking duration are pre-set

values, guaranteeing a perfect result every time -

automatically. These values are set using the C.O.P.^®

(Programmed Optimal Cooking) system. The

duration may be modified by ±5/10 minutes,

GRATIN mode

The top heating element and the rotisserie spit

(where present) are activated and the fan begins to

operate. During part of the cycle the circular heating

element is also activated. This combination of

features increases the effectiveness of the

unidirectional thermal radiation of the heating

elements through forced circulation of the air

throughout the oven.

depending on the selected cooking mode. The

cooking cycle stops automatically and the oven

indicates when the dish is cooked. You may start

cooking whether the oven has been preheated or not.

This helps prevent food from burning on the surface

and allows the heat to penetrate right into the food.

Always cook in this mode with the oven door closed.

! When the cooking stage has been reached, the oven

buzzer sounds.

! Do not open the oven door to avoid offsetting the

cooking time and temperature.

LOW TEMPERATURE modes

This type of cooking can be used for proving, defrosting,

preparing yoghurt and heating dishes at the required

speed. The temperature options are: 40, 65, 90 °C.

ROAST mode

Use this function to cook beef, pork and lamb. Place

the meat inside the oven while it is still cold. The

dish may also be placed in a preheated oven.

BAKED CAKES mode

This function is ideal for cooking desserts which are

made using natural yeast, baking powder and

desserts which contain no yeast. Place the dish in

the oven while it is still cold. The dish may also be

placed in a preheated oven.

PIZZA mode

BREAD mode

Use this function to make pizza. Please see the following

chapter for the recipe and further details.

To obtain the best results, we recommend that you

carefully observe the instructions below:

• "ollow the recipe.

• Do not exceed the maximum weight of the

dripping pan.

BREAD mode

Use this function to make bread. Please see the following

chapter for the recipe and further details.

• Remember to pour 100 ml of cold water into

the baking tray in position 5.

• The dough must be left to rise at room temperature

for 1 – 1 ½ hours (depending on the room

temperature) or until the dough has doubled in size.

PIZZA mode

To obtain the best results, we recommend that you

carefully observe the instructions below:

• "ollow the recipe.

Recipe for BREAD:

1 Dripping pan holding 1000 g Max, lower level

2 Dripping pans each holding 1000 g Max, medium and

lower levels

• The weight of the dough should be between 500 g

and 700 g.

• Lightly grease the dripping pan.

Recipe for 1000 g of dough: 600 g flour, 360 g water, 11g

salt, 25 g fresh yeast (or 2 sachets of powder yeast)

Method:

Recipe for PIZZA:

1 dripping pan on a low shelf level, hot or cold oven

Recipe for 3 pizzas weighing approximately 550 g: 1000

g flour, 500 ml water, 20 g salt, 20 g sugar, 100 ml olive

oil, 20 g fresh yeast (or 2 sachets of powder yeast)

• Leavening at room temperature: 1 hour.

• Place inside hot or cold oven.

• Mix flour and salt in a large bowl.

• Dilute yeast in lukewarm water (approximately 35

degrees).

• Make a small well in the mound of flour.

• Pour in water and yeast mixture.

• Start the

PIZZA cooking mode.

• Knead dough by stretching and folding it over

itself with the palm of your hand for 10 minutes

until it has a uniform consistency and is not too

sticky.

• Ball and cover the dough with plastic wrap and

leave it to leaven at room temperature for 1 – 1 ½

hours (until it has doubled in size).

• Cut the dough into equal sized loaves.

• Place them in the dripping pan on oven paper.

• Cover the loaves with flour.

• Make incisions on the loaves.

• Remember to pour 100 ml of cold water into

the baking tray in position 5. "or cleaning

purposes, we recommend the use of water and

vinegar.

• Place the loaves inside the oven while it is still cold.

• Start the

BREAD cooking mode.

• Once baked, leave the loaves on one of the grill racks

until they have cooled completely.

Programming cooking

Practical cooking advice

! A cooking mode must be selected before

! Do not place racks in position 1 and 5 during fan-

assisted cooking. This is because excessive direct

heat can burn temperature sensitive foods.

programming can take place.

Programming the duration

1. Press the

; button; the

button and the

! In the BARBECUE and GRATIN cooking modes,

particularly when using the rotisserie spit, place the

dripping pan in position 1 to collect cooking

residues (fat and/or grease).

numbers on the TIME display will flash.

2. To set the duration, press buttons "+" and "-";

press and hold to scroll the numbers quicker and

make setting easier.

3. Once the desired duration setting is reached, wait

10 seconds for the selection to be memorized, or

MULTILEVEL

press button

again to fix the setting.

• Use positions 2 and 4, placing the food which

requires more heat on 2.

4. When the set time has elapsed, END appears on

the TEMPERATURE display and a buzzer sounds.

• "or example: it is 9:00 a.m. and a time of 1 hour

and 15 minutes is programmed. The programme

will stop automatically at 10:15 a.m.

• Place the dripping pan on the bottom and the rack

on top.

BARBECUE

Programming delayed cooking

• Place the grill rack in position 3 or 4 and place

the food in the centre of the rack.

1. Press the

button and repeat steps 1 to 3 as

described for the duration setting.

2. Then press the

button and set the end of

• We recommend that the power level is set to

maximum. The top heating element is regulated

by a thermostat and may not always operate

constantly.

cooking time by pressing buttons "+" and "-"; press

and hold to scroll the numbers quicker and make

setting easier.

3. Once the end of cooking time is reached, wait 10

seconds for the selection to be memorized, or press

PIZZA

the

button again to fix the setting.

• Use a light aluminium pizza pan. Place it on the

rack provided.

4. Press the “START” button to confirm the

programming process.

"or a crispy crust, do not use the dripping pan as

it prevents the crust from forming by extending

the total cooking time.

5. When the selected time has elapsed, END appears

on the TEMPERATURE display and a buzzer sounds.

• "or example: it is 9:00 a.m. and a time of 1 hour

and 15 minutes is programmed and the end time

is set to 12:30. The programme will start

automatically at 11:15 a.m.

• If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza

halfway through the cooking process.

The

and

buttons will flash signalling that the

programmed mode has been set. After

programming, in the time before cooking starts, the

TIME display indicates the duration and end of

cooking time alternately.

To cancel a programming procedure press the

"STOP" button.

! When selecting a cooking mode, the

button is

activated whereas the

the cooking time, the

button is not. When setting

button is illuminated and

delayed cooking can be programmed.

Cooking advice table

Cooking

modes

ꢀoods

Weight

(in kg)

Rack position

Preheating

Recommended

temperature

(°C)

Cooking duration

(minutes)

standard

guide rails

sliding guide

rails

Multilevel*

Barbecue*

Gratin*

Pizza on 2 racks

Pies on two racks/cakes on 2 racks

Sponge cake on 2 racks (on the dripping pan)

Roast chicken + potatoes

Lamb

Mackerel

Lasagne

Cream puffs on 2 racks

Biscuits on 2 racks

Cheese puffs on 2 racks

Savoury pies

Mackerel

Sole and cuttlefish

Squid and prawn kebabs

Cod fillet

Grilled vegetables

1+1

2 and 4

1 and 2/3

1 or 2

2 and 4

1 and 3

3 or 4

1 and 3

Yes

220-230

180

170

200-210

190-200

180

190-200

190

210

200

20-25

30-35

20-25

65-75

45-50

30-35

35-40

20-25

10-20

20-25

20-30

15-20

10-15

8-10

10-15

15-20

10-12

3-5

70-80

55-60

30-35

70-80

60-70

60-75

70-80

40-45

0.7

0.5

0.8

0.7

4 or 5

4 or 6

100%

210

200

210

2 or 3

Veal steak

Sausages

Hamburgers

Toasted sandwiches (or toast)

Spit-roast chicken using rotisserie spit (where present)

Spit-roast lamb using rotisserie spit (where present)

Grilled chicken

Cuttlefish

Spit-roast chicken using rotisserie spit (where present)

Spit-roast duck using rotisserie spit (where present)

Roast veal or beef

Roast pork

Lamb

1.5

Low

temperature

Defrosting

Proving

Dish heating

Pasteurisation

Pizza (see recipe)

8ocaccia (bread dough)

Bread (see recipe)

2 or 3

60-90

Automatic

pizza

23-33

Automatic

bread

Automatic

baked cakes

Automatic

roast

Cakes made using leavened dough

Roasts

2 or 3

35-55

60-80

* The cooking times listed above are intended as guidelines only and may be modified according to personal tastes. Oven preheating times are set as standard and may not be

modified manually.

Precautions and tips

! This appliance has been designed and

• Do not rest heavy objects on the open oven door.

manufactured in compliance with international safety

standards. The following warnings are provided for

safety reasons and must be read carefully.

• The appliance should not be operated by people

(including children) with reduced physical,

sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with

the product. These individuals should, at the very

least, be supervised by someone who assumes

responsibility for their safety or receive

General safety

• The appliance was designed for domestic use

inside the home and is not intended for

commercial or industrial use.

preliminary instructions relating to the operation of

the appliance.

• The appliance must not be installed outdoors, even

in covered areas. It is extremely dangerous to

leave the appliance exposed to rain and storms.

• Do not let children play with the appliance.

• When moving or positioning the appliance, always

use the handles provided on the sides of the oven.

Disposal

• When disposing of packaging material: observe

local legislation so that the packaging may be

reused.

• Do not touch the appliance with bare feet or with

wet or damp hands and feet.

• The appliance must be used by adults only for the

preparation of food, in accordance with the

instructions provided in this booklet.

• The European Directive 2002/96/EC relating to

Waste Electrical and Electronic Equipment

(WEEE) states that household appliances should

not be disposed of using the normal solid urban

waste cycle. Exhausted appliances should be

collected separately in order to optimise the cost

of re-using and recycling the materials inside the

machine, while preventing potential damage to

the atmosphere and to public health. The

crossed-out dustbin is marked on all products to

remind the owner of their obligations regarding

separated waste collection.

• Do not touch the heating elements and parts of

the oven door when the appliance is in use;

these parts become extremely hot. Keep

children well away from the appliance.

• Ensure that the power supply cables of other

electrical appliances do not come into contact

with the hot parts of the oven.

• The openings used for the ventilation and

dispersion of heat must never be covered.

"or further information relating to the correct

disposal of exhausted household appliances,

owners may contact the public service provided

or their local dealer.

• Always grip the oven door handle in the centre:

the ends may be hot.

• Always use oven gloves when placing cookware

in the oven or when removing it.

Respecting and conserving the

environment

• Do not use aluminium foil to line the bottom of the

oven.

• You can help to reduce the peak load of the

electricity supply network companies by using the

oven in the hours between late afternoon and the

early hours of the morning. The cooking mode

programming options, the “delayed cooking”

mode (see Cooking modes) and “delayed

automatic cleaning” mode (see Care and

Maintenance) in particular, enable the user to

organise their time efficiently.

• Do not place flammable materials in the oven: If

the appliance is switched on accidentally, it could

catch fire.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from

the electricity mains.

• Always keep the oven door closed when using the

BARBECUE and GRATIN modes: This will achieve

improved results while saving energy

(approximately 10%).

• If the appliance breaks down, under no

circumstances should you attempt to perform the

repairs yourself. Repairs carried out by

inexperienced persons may cause injury or further

malfunctioning of the appliance. Contact a Service

Centre (see Assistance).

• Check the door seals regularly and wipe them

clean to ensure they are free of debris so that

they adhere properly to the door, thus avoiding

heat dispersion.

Care and maintenance

Switching the appliance off

Disconnect your appliance from the electricity supply

3. Grip the door on the two external sides and close

it approximately half way. Pull the door towards

before carrying out any work on it.

you, lifting it out of its slot (see diagram).

Cleaning the appliance

• The stainless-steel or enamel-coated external parts

and the rubber seals may be cleaned using a

sponge that has been soaked in lukewarm water

and neutral soap. Use specialised products for the

removal of stubborn stains. After cleaning, rinse and

dry thoroughly. Do not use abrasive powders or

corrosive substances.

To replace the door, reverse this sequence.

• The inside of the oven should ideally be cleaned

after each use, while it is still lukewarm. Use hot

water and detergent, then rinse well and dry with a

soft cloth. Do not use abrasive products.

• All accessories can be washed like everyday

crockery, and are even dishwasher safe.

• We recommend that detergents are not sprayed

directly onto the control panel, but that a sponge is

used instead.

Inspecting the seals

Check the door seals around the oven regularly. If the

seals are damaged, please contact your nearest After-

sales Service Centre (see Assistance). We recommend

that the oven is not used until the seals have been

replaced.

! Never use steam cleaners or pressure cleaners on

the appliance.

Replacing the light bulb

To replace the

oven light bulb:

Cleaning the oven door

Oven

compartment

Clean the glass part of the oven door using a sponge

and a non-abrasive cleaning product, then dry

thoroughly with a soft cloth. Do not use rough abrasive

material or sharp metal scrapers as these could

scratch the surface and cause the glass to crack. "or

more thorough cleaning purposes, the oven door may

be removed:

Lamp

Seal

Glass door

1. Open the oven door fully (see diagram).

1. Remove the glass cover using a screwdriver.

2. Remove the light bulb and replace it with a similar

one: Wattage 15 W, cap E 14.

Replace the glass cover, making sure the seal is

positioned correctly (see diagram).

2. Lift up and turn the small levers located on the two

hinges (see diagram).

Automatic cleaning with the CAST CLEAN

function

Safety devices

• The door is locked automatically as soon as the

temperature exceeds a certain value.

With the "AST CLEAN mode, the internal temperature

of the oven reaches 500°C. The pyrolytic cycle is

activated and burns away food and grime residues.

Dirt is literally incinerated.

• Should a malfunction occur, the heating elements

will switch off.

Keep children away from the appliance during the

automatic cleaning cycle as surfaces may become

very hot. Particles may ignite inside the oven due to

the spontaneous combustion process. There is no

cause for concern: this process is both normal and

hazard-free.

• Once the oven door has been locked, you cannot

change the duration and end time settings.

! Programming is possible only after selecting the

"AST CLEAN mode.

Before initiating the "AST CLEAN mode:

Programming delayed automatic cleaning

• Remove large or coarse food residues from inside of

the oven using a damp sponge. Do not use

detergents.

1. Press the

numbers on the TIME display will flash.

2. To set the duration, press buttons "+" and "-";

press and hold to scroll the numbers quicker and

make setting easier.

button; the

button and the

• Remove all accessories.

3. Once the desired end of cooking time is reached,

wait 10 seconds for the selection to be memorized,

• Do not place tea towels or pot holders over the oven

handle.

or press button

again to fix the setting.

4. When the selected time has elapsed, END appears

on the TEMPERATURE display and a buzzer sounds.

• "or example: it is 9:00 a.m. and the Economy (ECO)

"AST CLEAN mode level has been selected: default

set time 1 hour. 12:30 is selected as the end time.

The programme will start automatically at 11:30 a.m.

! If the oven is too hot, the pyrolytic cycle may not

start. Wait for the oven to cool down.

! The programme may only be started once the oven

door has been closed.

Programming has been set when the

and

buttons

To activate the "ast Clean mode, press the

button; the TIME display will show the default

duration of 1h30 (normal cycle) while the

TEMPERATURE display will indicate "nor"; pressing

the "+" button activates the intensive cycle "int",

which lasts 2h; the "-" button activates the economy

cycle "eco", lasting 1h.

flash. After programming, in the time before the "ast

Clean mode starts, the TIME display indicates the

duration and end of the "ast Clean mode alternately.

To cancel a programming procedure press the “STOP”

button.

Once the automatic cleaning cycle is over

You will have to wait until the temperature inside the

oven has cooled down sufficiently before you can open

the oven door. You will notice some white dust

deposits on the bottom and the sides of your oven;

remove these deposits with a damp sponge once the

oven has cooled down completely. Alternatively, you

can make use of the already heated oven, in which

case it is not necessary to remove the deposits, they

are completely harmless and will not affect your food in

any way.

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its working life than

us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08709 066 066

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08709 077 077

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 0870 6092094

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use

quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer be plugged into a mains socket, and the door cannot

be locked shut.

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective because

of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no

cost to you.

This guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY I7 THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you

registering your appliance with us and the parts being fitted by one of our authorised engineers. There

will be a charge for our engineer's time. To activate the extra parts warranty on your appliance, simply

call our registration line on 0870 6092094 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense

of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08709

088 088 (ROI 01 230 0233).

7ree Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where necessary, to

arrange for an engineer to call. If we cannot resolve the technical problem we will replace your machine

or, if you prefer, give you your money back.

Notes

03/2008 - 195068296.00

XEROX BUSINESS SERVICES

Graco Car Seat PM 1373AD User Manual
Grizzly Saw G0640X User Manual
Haier Flat Panel Television HTF21S32 User Manual
Hamilton Beach Iron 14515 User Manual
Harbor Freight Tools Automobile Accessories 46087 User Manual
Hayter Mowers Chipper 71620 User Manual
Hayter Mowers Lawn Mower 560F User Manual
Honeywell Security Camera HD3VC4SAX User Manual
Honeywell Smoke Alarm C7015A User Manual
IBM DVR EDR1600 User Manual