Honeywell Digital Camera VCC 600N P User Manual

Operation Manual  
OSD Color Camera  
INSTRALLATION  
The contents of the package  
Check the below contents  
8. When operation is incorrect or a malfunction is observed  
While operating, if any abnormal condition (strange sound,  
VCC-600N/P  
Mounting a lens  
1. Remove the Protective cap in front of the camera.  
2. Confirm the mount ring whether it is for C or CS.  
3. Attach the lens to the lens mount ring.  
4. If the lens has an Auto Iris mechanism, connect the iris cable to the  
LENS in rear of the camera.  
smell or smoke) or  
observed, stop using the camera immediately, turn the  
power off, then contact your supplier.  
a
malfunction (no pictures, etc.) is  
- VCC-600N/P Camera 1set  
Thank you for choosing Honeywell VCC-600N/P camera.  
Please read these instructions carefully before operating this unit,  
and retain this manual for future reference.  
- Auto Iris Lens Plug  
- L Type Wrench  
- Operation Manual (English)  
9. Cleaning  
In the case of having no iris amplifier : Set the slide switch to  
DC (Down side).  
In the case of having iris amplifier : Set the slide switch VSD  
(Upper side)  
When connecting Auto iris lens, be sure to use the connector to  
be recommended by manufacturer.( E4-191, ChuoMusen, Japan)  
If you have any problems with this camera, contact your local  
supplier to service.  
Turn the power off and wipe off the dirt with a dry soft  
cloth. If it is extremely dirty, use furniture cleaner to wipe it  
off. To clean the lens, use a blower or lens cleaning  
tissue. (available from any camera dealer)  
CAUTION for SAFETY OPERATION  
10. Do not shoot any source of bright light.  
1. Water and Moisture  
To prevent fire or shock hazard, do not expose this camera  
to rain or moisture.  
If the objects contain very bright areas, bright vertical or  
horizontal lines may appear on the screen. This is called  
"smear" , a Phenomenon which often occurs with solid  
- state pickups, and is not a malfunction.  
VSD LENS PIN CONFIGURATION  
DC IRIS LENS PIN CONFIGURATION  
3
4
3
4
①③  
②④  
①③  
②④  
2. Servicing  
1
2
1
2
Do not attempt to disassemble or repair by yourself.  
You may be exposed to dangerous voltage or other hazards.  
Note that all servicing is qualified service personnel.  
Modifications not approved by manufacturer could  
void the user's authority to operate the equipment.  
3. Power Sources  
To prevent electric shocks and risk of hazards, do NOT use  
more than the specified power source.  
4. Environment  
Do not install too warm or too cold place. Recommended  
operation temperature is between -5and 50℃  
5. Sunlight  
Do not point the camera at the sun. CCD can be damaged.  
6. Heavy Shock and Vibration  
Do not drop the camera or subject it to heavy shock of  
vibration.  
7. Install on an Unstable Place  
Do not place or install this camera on an unstable place,  
stand, tripod, bracket or table. That may cause serious injury  
to people or damage to appliance.  
1. Power(12V)  
3. Video Signal  
2. No Connection  
4. GND  
1. Control -  
3. Drive +  
2. Control +  
4. Drive -  
11. Damage Requiring service  
Unplug the camera from the power source and refer  
servicing to qualified service personnel under the following  
condition:  
Back focus adjustment  
1. In case of fixed focus lens  
Loosen the locking ring with L type wrench and set the focus ring  
of lens to infinity ( ).  
Tune the mount ring to get a clear picture( distance from camera  
to object is more than 23m) and fasten the locking ring.  
2. In case of zoom lens  
Loosen the locking ring with L type wrench and set the lens to the  
maximum telephoto position. Then turn the focus ring to focus.  
In the case of Auto iris lens only, shoot  
object or reduce the ambient light so that the aperture is fully open.  
Set the lens to its maximum wide angle position, and set the focus.  
Repeat step and , until the difference between focusing  
position and is smallest.  
A. If the power-supply cord or plug is damaged.  
B. If the camera has been exposed to rain or water.  
C. If liquid has been spilled, or objects have fallen into the camera.  
D. If the camera does not operate normally by following the operating  
instructions. Adjust only those controls that are covered by the  
operating instructions as an improper adjustment of other controls  
may result in damage and will often require extensive work by a  
qualified technician to restore the camera to its normal operation.  
E. If the camera has been dropped or the cabinet has been damaged.  
F . If the camera exhibits a distinct change in performance.  
G. Warranty is not covered in case of natural disaster or wrong  
Installation.  
a
comparatively dark  
When the best focusing point in found, fasten the locking ring.  
Connection of power supply  
Must be checked the power source from the external power supply  
before power on.  
SPECIFICATIONS  
TROUBLESHOOTING  
NAMES & FUNCTIONS  
OSD MENU  
MODEL NAME  
Operational  
Video Standard  
Image Sensor  
Total Pixel  
VCC-600N  
NTSC  
VCC-600P  
PAL  
Before sending the camera out for repair, check the items  
below. If the problem persists after checking these items,  
contact your service center.  
GENERAL SETUP  
SYNC  
BURST  
CONTRAST  
SYNC LEVEL adjustment (01255)  
BURST LEVEL adjustment (01255)  
DOWN BUTTON  
UP BUTTON  
SONY 1/3Super HAD CCD  
410,000 Pixels  
380,000 Pixels  
470,000 Pixels  
440,000 Pixels  
CONTRAST LEVEL adjustment  
(01100)  
Effective Pixel  
Scanning System  
Scanning Frequency  
Sync System  
In case of no image  
Is the coaxial cable attached securely?  
Are the power and voltage normal?  
Has the iris of the lens inside the camera been adjusted correctly?  
In case of unclear image  
Is the lens in focus?  
RETURN  
Return to the previous menu.  
525 Lines, 2:1 Interlace  
15.734kHz(H), 59.94Hz(V)  
625 Lines, 2:1 Interlace  
15.625kHz(H), 50Hz(V)  
(+) BUTTON  
ENTER BUTTON  
(-) BUTTON  
CAMERA SETUP  
AE MODE  
INTERNAL  
More than 50dB  
LENS MODE, SHUTTER, AGC, BRIGHTNESS, MAX AGC,  
MAX FIELDS, etc.  
AWC LOCK, AWC AUTO, ATW, INDOOR, OUTDOOR,  
MANUAL, etc.  
S/N Ratio  
LENS CONNECTOR  
0.1lx (F=1.2, 50IRE)  
0.001lx (F=1.2, 50IRE, MAX FIELDS x512)  
Min. illumination  
WB MODE  
Horizontal Resolution  
Video Output  
540 TV Lines  
Is the lens dirty?  
LENS  
BLC MODE  
OFF, BLC, WDR, BMB and  
VBS 1.0Vp-p / BNC  
MANUAL / DC / VSD  
Is the monitor adjusted correctly?  
※ Dirt of fingerprints on the lens can adversely affect the  
images. Gently wipe any dirt or fingerprints off the lens  
with a soft cloth or lens cleaning paper and cleaning  
fluid (commercially available).  
their level, area setting.  
Lens Iris Control  
Electronic Shutter  
AGC  
ENTER  
PZM SET  
Privacy Zone Masking function setting.  
Day Night, Night Day mode setting.  
Camera ID and Position setting.  
1/60 ~ 1/100,000 sec  
1/50 ~ 1/100,000 sec  
NIGHTSHOT  
CAMERA ID  
RETURN  
OFF - 36dB  
VIDEO  
CONT  
Back Light Compensation  
White Balance  
OFF / BLC / WDR / BMB  
Return to the previous menu.  
POWER  
DC12V  
AWC LOCK / AWC AUTO / ATW / INDOOR / OUTDOOR / MANUAL  
Electrical  
MEM FUNC. SETUP  
DNR MODE  
DC  
VSD  
Digital Noise Reduction mode  
Rated Voltage  
DC12V ± 2V  
1.5W (max)  
setting. (OFFLOWHIGH)  
Power Consumption  
DIMENSIONS  
-
+
MD  
PIP MODE  
QUAD MODE  
MD MODE  
D.ZOOM  
MIRROR  
RETURN  
Picture-in-picture mode setting.  
Quad display mode setting.  
Motion Detection mode setting.  
Digital Zoom setting. (OFF1.0x16.0x)  
Mirror mode setting. (OFFH.MIRRORV.MIRRORFLIP)  
Return to the previous menu.  
Mechanical & Environmental  
Lens Mount  
CS Mount  
181g  
Weight  
Dimensions  
61.6[W] x 52.4[H] x 77.8[D]mm  
Pantone Color 11C (Gray)  
Gray  
VIDEO OUTPUT  
Front & Rear Color  
Body Color  
POWER ON LED  
Composite Video  
Signal Output  
This LED is ON  
in power ON state.  
Operating Temp.  
Storage Temp.  
-10°C ~ +50°C  
SPECIAL SETUP  
SHARPNESS  
GAMMA  
LANGUAGE  
RETURN  
-20°C ~ +70°C  
Sharpness compensation setting. (0~15)  
Gamma compensation setting. (0.36~1/USER , 8steps)  
OSD Language setting. (ENG, KOR, JPN, CHI1, CHI2)  
Return to the previous menu.  
Operating Humidity  
90% RH (non-condensing)  
Lens Type Select Switch  
Unit: mm  
DC Lens: with no iris amp.  
VSD Lens: with iris amp.  
DEFAULT SETUP  
FACTORY DEFAULT  
RETURN  
Set to the Factory Default.  
Return to the previous menu.  
LENS  
ENTER  
VIDEO  
Power Input Terminal and MD Alarm Output  
EXIT SETUP  
SAVE AND EXIT  
EXIT  
Honeywell Security Group  
Honeywell Co., Ltd.  
Address: 5F, Sangam IT Tower, B4 - 4block, 1590  
Sangam-dong, Mapo-gu, Seoul 121-835, Republic of  
Korea  
CONT  
POWER  
DC12V  
DC  
VSD  
+
-
MD  
RETURN  
Return to the previous menu.  
Printed in Korea  
D-100073-001, REV.0  
TEL: +82 2 799 6020 / 6395 / 6006  
FAX: +82 2 792 9011  
 

Hamilton Beach Fryer 38540C SK03 120 V~ 60 Hz 1500 W User Manual
HANNspree Flat Panel Television DT12 10H1 User Manual
Hasbro Games Trickster Game User Manual
Hasselblad Camera Lens CFE 4 120 User Manual
Havis Shields Automobile Accessories C 3311 18 2 User Manual
Honeywell TV Cables 7845gsmr User Manual
Hotpoint Oven HWD24X User Manual
Hypertec Carrying Case N14508NHY User Manual
IBM Laptop P N 42T8184 User Manual
Ikelite Digital Camera A710IS User Manual