Honeywell Barcode Reader 4600g User Manual

4600g, 4600r, 4600rp, 4800i  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
日本: www.honeywellaidc.com をご覧ください。  
查看繁体版请登陆 www.honeywellaidc.com  
한글 www.honeywellaidc.com 로 이동합니다 .  
2D-02-QS Rev E  
1/12  
 
USB Connection  
Keyboard Wedge Connection  
 
Serial (RS-232) Connection  
Reading Techniques  
The view finder projects an aiming  
beam that should be centered over  
the bar code, but it can be  
positioned in any direction for a  
good read.  
Hold the scanner over the bar code,  
pull the trigger, and center the  
aiming beam on the bar code.  
The aiming beam is smaller when  
the scanner is closer to the code and larger when it is farther from the  
code. Hold the scanner close to smaller bar codes, and farther away  
from large bar codes to get a proper read.  
If the bar code is highly reflective (e.g., laminated), you may need to  
tilt the scanner at an angle so the bar code can be scanned.  
 
Standard Product Defaults  
The following bar code resets all standard product default settings.  
Standard Product Defaults  
 
Interface  
Scan the bar code that describes the PC or interface you are using.  
USB Keyboard (PC)  
RS-232  
Japan DOS/V  
USB Japanese Keyboard (PC)  
AT/PS2 Keyboard Wedge  
(Default)  
Emulate External Keyboard  
 
Keyboard Country  
Scan the Program Keyboard Country bar code below, then scan  
the numeric bar code(s) from the back of this sheet, then the Save  
bar code to program the keyboard for your country. As a general  
rule, the following characters are not supported by the scanner for  
countries other than the United States:  
@ | $ # { } [ ] = / ‘ \ < > ~.  
Program Keyboard Country  
Country Code  
Belgium  
Scan Country Code  
Scan  
1
8
2
3
4
7
Italy  
5
Denmark  
Norway  
9
Finland  
Spain  
10  
6
France  
Switzerland  
USA (Default)  
Germany/Austria  
Great Britain  
0
Save  
Note: For a complete list of country codes, see the User’s Guide for  
 
Trigger  
The following bar codes will allow you to use the reader in Manual  
Trigger mode (need to press the trigger to read) or Presentation  
mode (the reader is activated when it “sees” a bar code).  
Manual Trigger  
(Default)  
Presentation Mode  
Streaming Presentation™  
Note: Streaming Presentation Mode applies only to units with the  
Advanced Illumination feature. Units with the advanced  
illumination feature have a software revision of 31205480-118  
or newer.  
When in Streaming Presentation mode, the imager leaves the scan  
illumination on all the time and continuously searches for bar codes.  
Streaming Presentation Mode  
 
Reread Delay  
This sets the time period before the scanner can read the same bar  
code a second time. Setting a reread delay protects against  
accidental rereads of the same bar code.  
Medium Reread Delay  
Suffix  
If you want a carriage return after the bar code, scan the Add CR  
Suffix bar code. To add a tab after the bar code, scan the Add Tab  
Suffix bar code. Otherwise, scan the Remove Suffix bar code to  
remove the suffixes.  
Add CR Suffix  
Add Tab Suffix  
Remove Suffix  
 
Add Code ID Prefix to all Symbologies  
Scan the following bar code if you wish to add a Code ID prefix to all  
symbologies at once.  
Add Code ID Prefix To All Symbologies  
(Temporary)  
Note: For a complete list of Code IDs, see the User’s Guide for your  
Function Code Transmit  
When this selection is enabled and function codes are contained  
within the scanned data, the imager transmits the function code to the  
terminal. Charts of these function codes are provided in your User’s  
Guide. When the imager is in keyboard wedge mode, the scan code  
is converted to a key code before it is transmitted.  
Enable  
(Default)  
Disable  
 
Data Format Editor Instructions  
The following are abbreviated instructions for entering a data format.  
For complete instructions refer to your User’s Guide, available at our  
1. Scan the Enter Data Format symbol.  
2. Primary/Alternate Format: scan 0 for Primary Format  
3. Terminal Type: scan 099 for any terminal type  
4. Code I.D.: scan 99 for any bar code type  
5. Length: scan 9999 for any length bar code.  
6. Editor commands: use the Programming Chart that follows.  
7. Scan Save to save your entries.  
Enter Data Format  
Clear All Data Formats  
Save  
 
Programming Chart  
0
2
4
6
1
3
5
7
8
 
9
B
D
F
A
C
E
Save  
 
Visual Xpress™  
To obtain access to additional features for the imager, use Visual  
complete download instructions and descriptions of Visual Xpress  
features, refer to your User’s Guide.  
Technical Assistance  
Contact information for technical support, product service, and repair  
can be found at www.honeywellaidc.com.  
Limited Warranty  
product’s warranty information.  
User Documentation  
For localized versions of this document, and to download the User’s  
Guide, go to www.honeywellaidc.com.  
Patents  
For patent information, go to www.honeywellaidc.com/patents.  
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make changes in  
specifications and other information contained in this document without prior  
notice, and the reader should in all cases consult HII to determine whether  
any such changes have been made. The information in this publication does  
not represent a commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions contained  
herein; nor for incidental or consequential damages resulting from the  
furnishing, performance, or use of this material.  
 
This document contains proprietary information that is protected by copyright.  
All rights are reserved. No part of this document may be photocopied,  
reproduced, or translated into another language without the prior written  
consent of HII.  
© 2008-2012 Honeywell International Inc. All rights reserved.  
 
 

Grandstream Networks IP Phone GXP280 User Manual
HANNspree Flat Panel Television DT09 10U1 000 User Manual
Heat Glo LifeStyle Indoor Fireplace 7000XLT User Manual
Honeywell Home Security System 800 08091V3 User Manual
Hotpoint Refrigerator FFB6200AX User Manual
HP Hewlett Packard Electric Shaver HP6409 User Manual
Husqvarna Saw FS309 User Manual
hussman Refrigerator IGFP R3 User Manual
IBM Personal Computer 8171 User Manual
iHome Clock Radio IP45 User Manual