IMITATION DOME CAMERA With LED
95154
ASSEMBLY AND OPERATING INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS manual.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09k
8.
9.
Stay alert. Watch what you are doing, use common sense. Do not install the Imitation
Dome Camera when you are tired.
check for damaged parts. Before using the Imitation Dome Camera, any part that
appears damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving parts;
any broken parts or mounting fixtures; and any other condition that may affect proper
operation.Any part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the Imitation Camera Dome if the power switch does not turn the
Camera Dome on and off properly.
10. Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this product. Approved accessories are available from Harbor Freight Tools.
11. do not install the imitation dome camera if under the influence of alcohol or drugs.
Read warning labels if taking prescription medicine to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not install the unit.
12. only use 1.5V dc aa-Batteries. Always properly dispose of used batteries in accordance
to the guidelines for waste disposal in your community.
the warnings, precautions, and instructions discussed in this instruction manu-
al cannot cover all possible conditions and situations that may occur. it must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
13.
14.
WaRning: All batteries must be disposed of properly. Do not incinerate. Batteries
may burst, causing personal injury and/or property damage. Dispose of the used bat-
teries properly, as cadmium in the batteries is toxic. For disposable guidelines, check
with your local waste management guidelines in your community.
unpacKing
When unpacking, check to make sure that the product is intact and undamaged. If any
part are missing or broken, please call Harbor Freight Tools at: 1-800-444-3353
BatteRy inStallation
1.
2.
First, remove the battery cover by pressing in on the upper lip of the cover then pull it
out.
Next place two AA 1.5 VDC Batteries in the Battery Housing. Be sure that the polari-
ties (+ or -) of the batteries line up with the polarity signs in the battery housing. Finally
replace the battery cover. See Figure 1 on page 4.
SKU 95154
For technical questions, please call 1-800-444-3353
Page 3
cameRa inStallation
1.
2.
Chose a wall or ceiling location that allows you to mount the unit onto a solid surface
capable of sustaining the weight of the unit. It is recommended that you choose a location
that is out of the reach of pedestrians. If you cannot mount the camera to a wall stud, you
will need to use the Dry Wall Mounting Anchors and Wood Screws (both not included).
It is essential to proper mounting that you use the correct size screws and that you also
space the two screw correctly. The exact distance between the two screws is 2.659”
(67.59 mm) center to center. You can make a pattern of the mounting holes by placing
a piece of tracing paper over the back of the Imitation Dome Camera and trace the
mounting holes location using a pen or pencil. Next tape the pattern over the area that
you want to install the camera. Mark the center of each mounting hole by hammering
a nail through the pattern into the mounting surface. Attach the screws to the mounting
surface leaving about a 1/4” of the screws’ shanks exposed.
Warning: When mounting, be sure to avoid hammering into any electrical wiring.
3.
After the two mounting screw have been attached to the wall or ceiling, place the two
mounting holes on the camera over the screw heads. Press the Dome Camera over the
screw heads and twist the camera. This should secure it into place. Always be careful,
when drilling into a wall or ceiling, to avoid wires, pipe or cables that may be in the path
of the drill. Be aware that the Camera needs to be mounted securely so it will not fall off
the mounting and cause bodily injury.
note: The mounting holes on the Imitation Dome Camera are approximately 1/4” with 5/32”
slots. See Figure 4 below.
opeRation
Once the two AA batteries are installed in the Dome Camera, the LED light will
automatically blink in 5 second intervals until the batteries go dead. When the light stops
blinking, replace the batteries.
Mounting Holes
Battery Housing
FiguRe 1
note: There are no replacement parts available for this product.
SKU 95154
For technical questions, please call 1-800-444-3353
Page 4
|