OWNER’S/
OPERATOR’S
MANUAL
MODEL NO.
PF-448
CAUTION
For Safe Operation
Read Rules And
TRACTOR FRONT LOADER
PALLET FORK
Instructions Carefully
SINO LEEINGLES, PIDA AYUDA
A AIGUIEN QUE SI LO LEA
PARA QUE LE TRADUZCA LAS
MEDIDAS DE SEGURIDAD.
Safety Instructions
Tractor Preparation
Assembly & Mounting
Maintenance
Operating Instructions Repair Parts
CAUTION
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD
BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE
1. Select an area for assembly that is clean and free of any
6. After completing assembly, thoroughly inspect the
debris which might cause persons working on the
assembly to trip.
machine to be sure that all nuts, bolts, hydraulic fittings
or any other fastened assemblies have been thoroughly
tightened.
2. Do not lift heavy parts or assemblies. Use crane, jack,
tackle, fork trucks or other mechanical devices.
7. Before operating the machine, thoroughly read the
operation section of your operator’s manual.
3. Preview the assembly instructions in your operator’s
manual before proceeding further.
8. Before operating, read the maintenance section of your
operator’s manual to be sure that any parts requiring
lubrication, such as gearboxes, are full, to avoid any
possible damage.
4. If the assembly instructions call for parts or assemblies to
be blocked up, use only blocking material that is in good
condition and is capable of handling the weight of the
assembly to be blocked. Also insure that the blocking
material is on a clean, dry surface.
9. Before operating equipment – If you have any
questions regarding the proper assembly or
operation, contact your dealer or representative.
5. Never put hands, or any part of body, under blocked up
assemblies if at all possible.
LIMITED WARRANTY
Worksaver warrants to the original purchaser of any new Pallet Fork (Model PF-448), that the equipment
be free from defects in material and workmanship for a period of six (6) months for non-commercial, state,
and municipalities. Use sixty (60) days for commercial use from date of retail sale.
Replacement or repair parts installed in the equipment covered by this warranty are warranted for sixty
(60) days from the date of purchase of such part or to the expiration of the applicable new equipment
warranty period, whichever occurs later.
Such parts shall be provided at no cost to the user during regular working hours. Worksaver reserves
the right to inspect any equipment or parts which are claimed to have been defective in material or
workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Worksaver’s obligation under this warranty, to the extent allowed by law, is in lieu of all warranties, implied
or expressed, including implied warranties of merchantability and fitness for a particular purpose and any
liability for incidental and consequential damages with respect to the sale or use of the items warranted.
Such incidental and consequential damages shall include but not be limited to: transportation charges
other than normal freight charges; cost of installation other than cost approved by Worksaver; duty; taxes;
charges for normal service or adjustments; loss of crops or any other loss of income; rental of substitute
equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts
resulting from acts beyond the control of Worksaver.
THIS WARRANTY SHALL NOT APPLY:
1. To vendor items which carry their own warranties, such as hydraulic cylinders, tires, and tubes.
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.
3. If parts not made or supplied by Worksaver have been used in connection with the unit, if, in sole
judgement of Worksaver such use affects its performance, stability, or reliability.
4. If the unit has been altered or repaired outside of an authorized Worksaver dealership in a manner
which, in the sole judgement of Worksaver affects its performance, stability or reliability.
5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic
fluid, worn blades, or to normal deterioration of such things as belts and exterior finish, due to use or
exposure.
6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and other items that in
the company’s sole judgement is a wear item.
NO EMPLOYEE OR REPRESENTATIVE OF WORKSAVER IS AUTHORIZED TO CHANGE THIS
WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN
WRITING AND SIGNED BY WORKSAVER’S SERVICE MANAGER, POST OFFICE BOX 100, LITCHFIELD,
ILLINOIS 62056-0100.
Download from Www.Somanuals.com. 2All Manuals Search And Download.
To the Owner/Operator/Dealer
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded opera-
tor who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this
implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!!
Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
THIS SAFETY ALERT SYMBOL IDENTIFIES IMPORTANT
SAFETY WARNING MESSAGES. CAREFULLY READ EACH
WARNING MESSAGE THAT FOLLOWS. FAILURE TO
UNDERSTAND AND OBEY A SAFETY WARNING, OR
RECOGNIZE A SAFETY HAZARD, COULD RESULT IN AN
THIS SYMBOL MEANS
INJURY OR DEATH TO YOU OR OTHERS AROUND YOU.
THE OPERATOR IS ULTIMATELY RESPONSIBLE FOR THE
SAFETY OF HIMSELF, AS WELL AS OTHERS, IN THE
OPERATING AREA OF THE SKID STEER UNIT OR
TRACTOR AND ATTACHED EQUIPMENT.
– ATTENTION!
– BECOME ALERT!
– YOUR SAFETY IS INVOLVED!
UNDERSTAND SIGNAL WORDS
Note the use of the signal words DANGER, WARNING
and CAUTION with the safety messages. The
appropriate signal word for each has been selected
using the following guidelines:
WARNING: Indicates a potentially hazardous sit-
uation that, if not avoided, could result in death
or serious injury, and includes hazards that are
exposed when guards are removed. It may also
be used to alert against unsafe practices.
DANGER: Indicates an imminently hazardous situation
that, if not avoided, will result in death or serious injury.
This signal word is to be limited to the most extreme
situations typically for machine components which, for
functional purposes, cannot be guarded.
CAUTION: Indicates a potentially hazardous sit-
uation that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
If you have questions not answered in this manual or require additional copies or the manual is damaged, please
contact your dealer or the manufacturer directly.
IMPORTANT SAFETY INFORMATION!
Working with unfamiliar equipment can lead to careless injuries. Read this manual, and the manual for your tractor,
skid steer, or forklift, before assembly or operating, to acquaint yourself with the machines. It is the implement owner’s
responsibility, if this machine is used by any person other than yourself, is loaned or rented, to make certain that the
operator, prior to operating:
1. Reads and understands the operator’s manuals.
2. Is instructed in safe and proper use.
The use of this equipment is subject to certain hazards which cannot be protected against by mechanical
means or product design. All operators of this equipment must read and understand this entire manual,
paying particular attention to safety and operating instructions, prior to using. If there is something in this
manual you do not understand, ask your supervisor, or your dealer, to explain it to you.
3
SAFETY INSTRUCTIONS (continued)
EQUIPMENT SAFETY GUIDELINES
Safety of the operator is one of the main concerns in designing and developing a new piece of equipment.
Designers and manufacturers build in as many safety features as possible. However, every year many
accidents occur which could have been avoided by a few seconds of thought and a more careful approach to
handling equipment.You, the operator, can avoid many accidents by observing the following precautions in this
section. To avoid personal injury, study the following precautions and insist those working with you, or for you,
follow them.
In order to provide a better view, certain photographs or illustrations in this manual may show an assembly with
a safety shield removed. However, equipment should never be operated in this condition. Keep all shields in
place. If shield removal becomes necessary for repairs, replace the shield prior to use.
Replace any CAUTION, WARNING, DANGER or instruction safety sign that is not readable or is missing.
Location of such safety signs is indicated in this booklet.
Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating this
equipment. Consult your doctor about operating this machine while taking prescription medications.
Review the safety instructions with all users annually.
This equipment is dangerous to children and persons unfamiliar with its operation. The operator should be a
responsible adult familiar with farm machinery and trained in this equipment’s operations. Do not allow per-
sons to operate or assemble this unit until they have read this manual and have developed a thorough
understanding of the safety precautions and of how it works.
To prevent injury or death, use a tractor equipped with a Roll-Over Protective System (ROPS). Do not paint
over, remove or deface any safety signs or warning signs on your equipment. Observe all safety signs and
practice the instruction on them.
Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely, is in question –
DON’T TRY IT.
Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and
could affect the life of the equipment.
In addition to the design and configuration of this implement, including Safety Signs and Safety Equipment,
hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper
training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also
to Safety Messages and Operation Instructions in each of the appropriate sections of the Tractor, Skid Steer,
and Implement Manuals. Pay close attention to the Safety Signs affixed to the Tractor, Skid Steer, and the
Implement.
Download from Www.Somanuals.com. 4All Manuals Search And Download.
SAFETY INSTRUCTIONS (continued)
SAFETY TRAINING
Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to pro-
vide safe equipment can be wiped out by a single careless act of an operator.
In addition to the design and configuration of equipment, hazard control and accident prevention are
dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation,
transport, maintenance and storage of equipment.
It has been said, “The best safety device is an informed, careful operator.” We ask you to be that kind of an
operator. It is the operator’s responsibility to read and understand ALL Safety and Operating instructions in the
manual and to follow these. Accidents can be avoided.
Working with unfamiliar equipment can lead to careless injuries. Read this manual, and the manual for your
tractor, before assembly or operating, to acquaint yourself with the machines. It is the equipment owner’s
responsibility, if this machine is used by any person other than yourself, is loaned or rented, to make certain
that the operator, prior to operating:
1. Reads and understands the operator’s manuals.
2. Is instructed in safe and proper use.
Know your controls and how to stop skid steer, tractor, engine, and loader quickly in an emergency. Read this
manual and the one provided with your tractor or skid steer.
Train all new personnel and review instructions frequently with existing workers. A person who has not read
and understood all operating and safety instructions is not qualified to operate the machine. An untrained oper-
ator exposes himself and bystanders to possible serious injury or death.
Do not allow children to operate this machine.
5
SAFETY INSTRUCTIONS (continued)
SAFETY SIGNS
Keep safety signs clean and legible at all times.
Replace safety signs that are missing or have become illegible.
Replaced parts that displayed a safety sign should also display the current sign.
Safety signs are available from your Distributor or Dealer Parts Department or the factory.
How to Install Safety Signs:
Be sure that the installation area is clean and dry.
Be sure temperature is above 50°F (10°C).
Decide on the exact position before you remove the backing paper.
Remove the smallest portion of the split backing paper.
Align the sign over the specified area and carefully press the small portion with the exposed sticky backing in
place.
Slowly peel back the remaining paper and carefully smooth the remaining portion of the sign in place.
Small air pockets can be pierced with a pin and smoothed out using the piece of sign backing paper.
STARTING AND STOPPING SAFETY
Be certain the tractor or skid steer is in neutral or park position before starting engine.
Always shut off power unit and shift to “Park” or set brakes when leaving unit. Always lower bucket or
attachment to ground, relieve all hydraulic pressure. Remove key when leaving equipment unattended. Park in
level area.
Before operating equipment: if you have any questions regarding the proper assembly or operation, contact
your dealer or representative.
Download from Www.Somanuals.com. 6All Manuals Search And Download.
SAFETY INSTRUCTIONS (continued)
OPERATIONAL SAFETY
The use of this equipment is subject to certain hazards which cannot be protected against by mechanical
means or product design. All operators of this equipment must read and understand this entire manual, pay-
ing particular attention to safety and operating instructions, prior to using. If there is something in this manu-
al you do not understand, ask your supervisor, or your dealer, to explain it to you.
Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders fifty feet (50’) from
an operating power unit and attached equipment. Only properly trained people should operate this machine.
It is recommended the tractor be equipped with a Rollover Protection System (ROPS) and a seat belt that is
used. Always stop the tractor, skid steer, or forklift, set brake, shut off the engine, remove the ignition key, and
lower loader and attachment to the ground before dismounting. Never leave equipment unattended with the
engine running.
Please remember it is important that you read and heed the safety signs on the front loader attachment and
loader, and the safety rules set forth. Clean or replace all safety signs if they cannot be clearly read and under-
stood. They are there for your safety as well as the safety of others. The safe use of this machine is strictly
up to you, the operator.
Be sure power unit is in good condition. Read all the safety precautions and make sure all operators are famil-
iar with the safety rules of operation.
Know your controls and how to stop the power unit and engine quickly in an emergency. READ THIS MANU-
AL AND THE ONE PROVIDED WITH YOUR TRACTOR AND LOADER, OR SKID STEER.
When the use of hand tools is required to perform any part of assembly, installation, adjustment, maintaining,
repairing, removal, or moving the implement, be sure the tools used are designed and recommended by the
tool manufacturer for that specific task.
Personal protection equipment including safety glasses, safety shoes, and gloves are recommended during
assembly, installation, operation, adjustment, maintaining, repairing, removal, or moving the attachment.
Always use two people to handle heavy, unwieldy components during assembly, installation, removal, or
moving the loader attachment.
Never place any part of your body where it would be in danger if movement should occur during assembly,
installation, operation, maintaining, repairing, removal, or moving the implement.
The use of any loader attachment is NOT recommended on tractor with a tricycle wheel arrangement. Tricycle
type tractors are unstable for front loader use.
A heavy load can cause instability in driving a power unit. Make sure the front or rear of the power unit is
properly counter-balanced with weights. Always drive slowly – especially around turns. An unstable power unit
could steer badly and possibly tip over, causing injury or death.
Do not allow others to ride on the power unit with an operator. Riders are subject to injury such as being struck
by foreign objects or being thrown off. Riders obstruct the operator’s view resulting in unsafe operation. Never
allow anyone to ride on the implement!
7
SAFETY INSTRUCTIONS (continued)
OPERATIONAL SAFETY (continued)
Before you operate any equipment, check over all pins, bolts and connections to be sure all are securely in
place. Replace any damaged or worn parts immediately.
Do not work under a raised loader unless it is securely blocked or held in position. Do not depend on the power
unit hydraulic system to hold the implement in place.
Operate the loader controls smoothly, avoiding jerky operation. Stop loader gradually when lowering or lifting
loads.
Beware of low electrical wires when loader is raised. Serious injury or death can result if contact is made.
When handling material on a slope, always approach the material with the power unit facing uphill.
Only use a power unit equipped with a ROPS cab or rollover protective structure.
When stacking material, ALWAYS MAKE SURE MATERIAL IS PLACED SO THE STACK IS STABLE.
Keep all bystanders at a safe distance. REMEMBER FALLING ITEMS CAN ROLL OR TUMBLE.
Do not handle loads that exceed the weight limitations of the loader.
Carry the loads slowly and as low as possible to the ground. Avoid excessive speed during operation.
For operator safety, always keep load in front of power unit. NEVER position load back over operator. ALWAYS
BE CAREFUL!
Beware of lift clearance when raising loader to maximum height.
Keep alert and watch the rear as well as the front when working with the loader.
Download from Www.Somanuals.com. 8All Manuals Search And Download.
SAFETY INSTRUCTIONS (continued)
OPERATIONAL SAFETY (continued)
When maneuvering close to buildings or passing through narrow areas, be sure to allow sufficient clearance
for the power unit, loader, and load. Drive slowly.
Operate loader from operator’s seat only. Remain at controls until operating cycle is complete.
Use extreme care when working on inclines and hillsides.
Do not operate close to ditches, creeks or holes. Slow down when operating over rough ground.
Allow for additional length of loader and load on power unit while turning.
Keep load centered on attachment and loader. Unbalanced loads increase possibility of tipping or roll-over.
Never allow anyone to walk or work under a raised loader.
Be sure that people, livestock, or pets are not standing near the machine while operating.
Do not use loader for a work platform.
Do not lift or carry anyone on loader or in bucket or on attachment.
ALWAYS lower loader to the ground or block securely before performing any maintenance work.
Always keep power unit on solid footing when operating loader.
Observe Safety Recommendations in loader instruction manual.
Inspect the entire machine periodically as indicated in the Maintenance Section of this manual. Look for loose
fasteners, worn or broken parts, pinched hydraulic hoses, and leaky or loose fittings. Make sure all pins have
cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order.
9
SAFETY INSTRUCTIONS (continued)
TRANSPORT SAFETY
Comply with state and local laws governing highway safety and movement of farm machinery on public roads.
The use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use.
Local laws should be checked for all highway lighting and marking requirements.
When driving the tractor and equipment on the road or highway under 20 mph (32 kph) at night or during the
day, use flashing amber warning lights and a slow moving vehicle (SMV) identification emblem.
Always be sure the implement is in the proper raised position for transport.
Reduce speed when transporting mounted implements to avoid bouncing and momentary loss of steering
control.
Plan your route to avoid heavy traffic.
Always install transport locks, pins or brackets before transporting.
Do not drink and drive!
Watch for traffic when operating near or crossing roadways.
Turn curves or go up or down hills only at a low speed and at a gradual steering angle. Make certain that at
least 20% of the tractor’s weight is on the front wheels to maintain safe steerage. Slow down on rough or
uneven surfaces, and loose gravel.
Use extreme care and maintain minimum ground speed when transporting on hillside, over rough ground and
when operating close to ditches or fences. Be careful when turning sharp corners.
Never allow riders on either power unit or implement. Falling off can kill.
Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges, inter-
sections, etc.
Do not exceed 20 mph (32 kph). Reduce speed on rough roads and surfaces.
Always disengage PTO before driving the tractor to transport the implement from one place to another.
10
SAFETY INSTRUCTIONS (continued)
MAINTENANCE SAFETY
Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.
Follow good shop practices.
- Keep service area clean and dry.
- Be sure electrical outlets and tools are properly grounded.
- Use adequate light for the job at hand.
Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed building.
The exhaust fumes may cause asphyxiation.
Before working on this machine, drive to a level area, disengage the PTO, lower implement or loader (or if
working underneath, raise and block securely), shut off the engine, relieve all hydraulic pressure, set the
brakes, and remove the ignition keys.
Be certain all moving parts on attachments have come to a complete stop before attempting to perform
maintenance.
Never work under equipment unless it is blocked securely. Never depend on hydraulic system to keep imple-
ment in raised position.
Keep all persons away from operator control area while performing adjustments, service, or maintenance.
Always use personal protection devices such as eye, hand and hearing protectors, when performing any
service or maintenance.
Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to ensure unit
is in a safe condition.
When completing a maintenance or service function, make sure all safety shields and devices are installed
before placing unit in service.
Openings in the skin and minor cuts are susceptible to infection from hydraulic fluid. If injured by escaping
hydraulic fluid, see a doctor at once. Gangrene and death can result. Without immediate medical treatment,
serious infection and reactions can occur.
Download from Www.Somanuals1.c1om. All Manuals Search And Download.
SAFETY INSTRUCTIONS (continued)
MAINTENANCE SAFETY (continued)
After servicing, be sure all tools, parts and service equipment are removed.
Check to ensure all safety signs are installed and in good condition. (See safety sign section for location
drawing.)
Do not allow grease or oil to build up on any deck or platform.
Never replace hex bolts with less than grade five bolts unless otherwise specified, i.e. shear bolts. Refer to bolt
torque chart for head identification marking.
Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement
parts must be used to restore your equipment to original specifications.The manufacturer will not claim respon-
sibility for use of unapproved parts and/or accessories and other damages as a result of their use.
If equipment has been altered in any way from original design, the manufacturer does not accept any liability
for injury or warranty.
A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance on this
equipment.
STORAGE SAFETY
Following operation or when unhooking, stop the skid steer or tractor, set the brakes, shut off the engine,
relieve all hydraulic pressure and remove the ignition keys.
Store the unit in an area away from human activity.
Do not park equipment where it will be exposed to livestock for long periods of time. Damage and livestock
injury could result.
Do not permit children to play on or around the stored unit.
Make sure all parked machines are on a hard, level surface and engage all safety devices.
If blocking is used, make sure it is solid and secure before leaving area.
12
SAFETY SIGNS
REPLACE
SAFETY DECALS
IF DAMAGED
OR MISSING!
SAFETY INFORMATION
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped out
by a single careless act of an operator.
In addition to the design and configuration of equip-
ment, hazard control and accident prevention are
dependent upon the awareness, concern, prudence
and proper training of personnel involved in the
operation, transport, maintenance and storage of
equipment.
It has been said, “The best safety device is an
informed, careful operator.” We ask you to be that
kind of an operator.
When working on side hills, DO NOT RAISE
LOADER TOO HIGH. Keep an eye on terrain
changes. Keep load low.
ALWAYS OBEY ALL SAFETY RULES!
ALWAYS BE CAREFUL!
Download from Www.Somanuals1.c3om. All Manuals Search And Download.
INSTRUCTIONS
The Universal Pallet Fork attachment is designed to fit
most farm tractor double-cylinder front-end loaders.
Optional brackets are available to fit some popular quick
coupler front-end loaders.
Be sure tires and rims are in good condition. Inflate
tires to the proper recommended air pressure.
The Universal Pallet Fork will also work on the rear of
tractors with a Category II 3 pt. hitch.
WARNING!
Power unit must be equipped with ROPS or ROPS
cab and seat belt. Keep seat belt securely fastened.
Falling off power unit can result in death from being
run over or crushed. Keep foldable ROPS systems in
“locked up” position at all times.
The model PF-448 with 48” solid pallet forks can han-
dle loads up to 4,000 lbs. Load ratings are figured with
the load about 20” in front of the fork lift frame and even-
ly distributed between the two fork tines. NEVER put load
at the ends of the fork tines – the lift capacity at the ends
1
3
of the forks is only about / of the total lift capacity.
WARRANTY DOES NOT COVER BENT FORKS.
CAUTION!
Be sure your tractor and loader are in good condi-
tion. Read all the safety precautions and make sure
all equipment operators are familiar with the safety
rules of operation.
TRACTOR REQUIREMENTS
AND PREPARATION
——————————————————
The required size of the tractor and front loader or skid
steer will be determined by the weight of the load to be
handled.
The operator is responsible for the safe operation of this
equipment. The operator must be properly trained.
Operators should be familiar with the tractor, loader and
loader attachment, and all safety practices before start-
ing operation. Read the safety rules and safety signs on
pages 3-13.
Always use a tractor and front loader or skid steer large
enough to safely handle the load.
Check your tractor and front loader or skid steer to
make sure they are in good working condition. Check all
frame mounting bolts to make sure they are tight.
Loaders that attach to the tractor frame rails should
have a cross-tie installed for stability.
WARNING!
A heavy load can cause instability in driving a
tractor. Make sure the rear of the tractor is properly
counter-balanced with weights. Always drive slowly
– especially around turns. An unstable tractor could
steer badly and possibly tip over, causing injury or
death.
WARNING!
The use of any loader attachment is NOT recom-
mended on tractors with a tricycle wheel arrange-
ment. Tricycle type tractors are unstable for front
loader use.
NOTE: Loaders with only one hydraulic cylinder in the
center of the loader to tilt the bucket or attachment may
be used with the addition of an optional center bracket
(order bracket #830320).
ASSEMBLY – TRACTOR LOADERS
PIN ON ATTACHMENT
——————————————————
This unit is shipped almost completely assembled.
Carefully follow instructions for final assembly.
Check the tractor’s hydraulic system. Be sure the
hydraulic oil and filter have been serviced according to
manufacturer’s recommendations. Refer to your tractor or
loader operator’s manual or dealer for any adjustments
necessary to put the hydraulic system in good working
order.
Preview the assembly instructions and the exploded
views of the pallet fork in your operator’s manual and
become familiar as to how the parts or assemblies go
together.
14
INSTRUCTIONS (continued)
ASSEMBLY (continued)
ASSEMBLY – QUICK ATTACH
—————————————————— ——————————————————
Remove the bucket from your front end loader. Check
your loader to make sure it is in good working order. Check
all frame mounting bolts to make sure they are tight.
If your tractor loader has a bucket Quick Attach feature,
check with your dealer on the availability of adapter
brackets for your brand and model loader.
Measure the width of the front adapter on your loader
and locate the Quick Attach brackets on the main frame.
Locate these brackets so the main frame will be centered
on your loader.
Loaders that attach to the tractor frame rails should
have a cross-tie installed for stability.
Refer to the “exploded view” of the Loader Fork on page
18 of this manual.
Tighten the U-bolts that connect the brackets to the
main frame.
Assemble the two lift brackets (Ref. #3) on the main
5
8
frame (Ref. #1) with the / ” x 3” I.D. U-bolts. Leave the
U-bolts loose.
NOTE: The lift channel brackets are supplied with 1”
ASSEMBLY – TRACTOR LOADERS
——————————————————
Install the pallet forks on the main frame. The forks go
on in the center of the main frame and then are slid to the
right or left side.
1
8
diameter pins to fit your loader. If your loader requires 1 / ”
pins, it will be necessary for the hole diameter in the
5
32
channel brackets to be drilled out to 1 / ” (1.156”) and ask
1
1
8
8
your dealer to order 1 / ” diameter pins. The 1 / ” pins are
1
8
part #830318. Be sure to indicate if two or four 1 / ” pins
are required.
NOTE: Smearing a light coat of grease on the main frame
rails will make adjusting the fork width easier.
1
4
If your loader requires 1 / ” diameter pins, please ask
your dealer to order adapter bushings (part #830319). Be
sure to indicate how many adapter bushings are required.
IMPORTANT: Keep forklift tines adjusted to maximum
width for better load stability.
NOTE: The Ford (New Holland) models 7109, 7209,
7210, 7309, 7310 and 7410 Pin Type Loaders require
special brackets. Also, Rhino (Alamo) models 2410 and
2491. Order #830330 bracket kit.
PRE-OPERATION CHECKLIST
——————————————————
NOTE: For loaders that require brackets that provide
(OWNER/OPERATOR RESPONSIBILITY)
additional roll back, order #830335 (1” pins).
____ Review and follow safety rules and safety signs on
pages 3 through 13.
Connect the above assembly to the loader arms using
the bottom hole in the channel and attach the upper con-
trol cylinder to the top hole in the lift channels. Center the
____ Check that Loader Fork is properly and securely
attached to tractor loader.
main frame (side to side) with your loader arms and
5
8
tighten the four (4) / ” x 3” U-Bolts.
____ Check that all hardware is properly installed.
The lower hole positions in the lift channels can be used
to obtain more angle movement. However, if the frame
becomes too parallel with the loader lift arms, the loader
may not have enough power (mechanical advantage) to
bring the frame back.
____ Check that no one enters the area of machine oper-
ation. Always work at a safe distance from roads,
built-up areas, or populated places.
____ Know your controls and how to stop tractor, engine
and PTO quickly in an emergency. READ THIS
MANUAL AND THE ONE PROVIDED WITH YOUR
TRACTOR AND LOADER.
NOTE: Generally, it is not recommended to have the tilt
cylinders located any closer than 10-12 inches to the
main loader lift arms. Check the spacing of mounting
pins on your loader bucket and use this as a guide.
____ To avoid accident or injury, do not allow anyone to
operate this equipment without proper instructions.
Any person who operates this equipment must be
instructed in and be capable of the safe operation
of the tractor, implement and all controls.
If tilt cylinders are located too close to the loader arms,
they may go “over center” when fully extended. If this
happens, damage may occur to the cylinders and/or
mounting brackets.
Download from Www.Somanuals1.c5om. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Make sure all operators have read the Owner’s Manual
and are familiar with the instructions and the safety rules
of operation.
OPERATION
——————————————————
Be sure tractor or skid steer is properly counter-
balanced with weights before attempting to lift any load.
Make sure fork latch is properly engaged.
OPERATE LOADER SAFELY
——————————————————
Using the bucket tilt cylinders, adjust the angle of the
fork tines so they are parallel with the ground.
• Improper use of loader can cause serious injury or
death.
Adjust height of fork tines to enter the pallet to be
handled. Always keep the load or pallet as close to the
forklift main frame as possible.
• Become familiar with controls.
• Be sure anyone operating the loader is aware of safe
operation and potential hazards. Read and observe
safety recommendations in loader manual.
Make sure weight of load is centered between the forks.
• Operate loader from operator’s seat only. Remain at
controls until operating cycle is complete.
CAUTION!
Never exceed the lift capacity of the tractor/loader
• Stop loader gradually when lowering or lifting loads.
or skid steer used with the loader fork.
• Use particular care when working on inclines and hill-
sides.
• Avoid holes, ditches, and obstructions which may
cause tractor/loader to tip.
CAUTION!
Avoid carrying loose or shiftable loads. Falling
items could cause injury.
• Allow for additional length of loader on tractor while
turning.
• Never allow anyone to walk or work under a raised
loader.
WARNING!
The Model PF-448 Pallet Fork is NOT to be used for
large round bales, as this would create a hazardous
condition.
• Be sure that people, livestock, or pets are not standing
near the machine while operating.
• Do not use the loader for a work platform.
• Do not lift or carry anyone on loader or in bucket or
attachment.
WARNING!
• Carry load low.
Beware of low electrical wires when loader is
raised. Serious injury or death can result if contact is
made.
• Travel slowly over rough ground or when making turns.
• Drive slowly through gates and doors.
• Avoid carrying loose or shiftable loads.
CAUTION!
Beware of lift clearance when raising loader to max-
• Lower bucket or attachment to ground when loader is
unattended.
imum height.
16
OWNER SERVICE
MAINTENANCE
TRANSPORTING
—————————————————— ——————————————————
WARNING!
CAUTION!
Always stop the tractor or skid steer, set brake,
shut off engine, remove key, and lower loader to
ground before attempting to service. Never leave
equipment unattended with engine running.
When traveling on public roads, whether at night or
during the day, use accessory light and devices for
adequate warnings to operators of other vehicles.
Comply with all federal, state and local laws.
Check visibility. If visibility is impaired, reduce speed or
consider other means of transport.
WARNING!
Allow for additional length of loader on tractor while
turning. Carry load low.
Do not work under a raised loader unless it is
securely blocked or held in position. Do not depend
on the hydraulic system to hold loader and attach-
ment in place.
Select a safe ground travel speed when transporting
from one area to another. When traveling on roadways,
transport in such a way that faster moving vehicles may
pass you safely.
Check the pins at the ends of the loader arms. Make
sure they are locked in place with the linchpins.
When traveling over rough or hilly terrain or when
making turns, slow down and use extra care.
Periodically check all bolts to make sure they are tight.
Read all the safety warnings in the front of this manu-
al and in the manual of tractor or skid steer unit.
Replace any worn or damaged parts immediately. Do
not use attachment with any damaged parts.
STORAGE
——————————————————
• At the end of the working season or when the pallet
fork will not be used for a long period, it is good
practice to clean off any dirt or grease that may have
accumulated.
• Inspect the pallet fork for loose, damaged or worn
parts and adjust or replace if needed.
REPLACE
SAFETY SIGNS
IF DAMAGED
OR MISSING.
• Sand areas where paint is chipped or worn and repaint
to prevent rust.
• Always store in a safe place away from children or
livestock.
Download from Www.Somanuals1.c7om. All Manuals Search And Download.
MODEL PF-448 PARTS LIST
18
SAFETY PRECAUTIONS
MOST ACCIDENTS OCCUR BECAUSE OF NEGLECT OR CARELESSNESS.
AVOID NEEDLESS ACCIDENTS BY FOLLOWING ALL OF THE SAFETY PRECAUTIONS LISTED BELOW.
•
•
Machinery should be operated only by those who are
responsible and are authorized to do so.
•
•
Reduce speed when transporting mounted implements
to avoid bouncing and momentary loss of steering
control.
Stop the engine, lower all equipment, lock the brakes,
and remove the ignition key before dismounting from the
tractor.
A heavy load can cause instability of the tractor. Use
extreme care during road travel. Slow down on turns and
watch out for bumps. Tractor may need front counter-
weights to counter-balance the weight of the implement.
•
•
•
•
Never stand between tractor and implement while tractor
is being backed to hitch.
•
Reduce speed on hillsides or curves so there is no
danger of tipping.
Loose fitting clothing should not be worn, to avoid catch-
ing on various parts.
•
•
Avoid driving too close to the edge of ditches or creeks.
Detach implement in area where children normally do not
play.
Do not transport implement on public roads without
reflectors and slow moving vehicle emblem in daylight
and with approved warning lights at night and other
periods of poor visibility.
When performing adjustments or maintenance on an
implement, first lower it to the ground or block it securely
at a workable height.
•
•
•
Due to the width of some implements, use extra caution
on highways, farm roads, and when approaching gates.
•
•
•
Only a qualified operator should be permitted on tractor
when in operation; no riders allowed.
Make certain everyone is in the clear before starting
tractor or raising or lowering equipment.
Always be sure the implement is in the proper position for
transport.
Operate the tractor and implement only while seated in
the driver’s seat.
Keep alert and watch the front as well as the rear when
working with the implement.
TRACTOR FRONT LOADER
OWNER’S/
OPERATOR’S
MANUAL
PALLET FORK
✔ Please work, drive, play, and live each day with
care and concern for your safety and that of your
family and fellow citizens.
MODEL NO.
PF-448
WHEN ORDERING REPAIR
PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
MAKE EVERY DAY A
HOLIDAY FROM ACCIDENTS!
1. PART NUMBER
2. PART DESCRIPTION
3. MODEL NUMBER
4. NAME OF ITEM
MAY 2006
WORKSAVER, INC.
P.O. BOX 100 LITCHFIELD, IL 62056-0100 (217) 324-5973
WS-TA004-OG
|