E V P - P S E R I E S P O W E R E D L O U D S P E A K E R S
EVP-P SERIES PROFESSIONAL SPEAKER
SYSTEMS USER MANUAL
EVP-12P, EVP-12PM, EVP-15P, EVP-15PM & EVP15PSB.
ƽ W ARNING & SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS carefully before operating this product.
RETAIN these instructions.
with an extension cable unless the pins can be fully inserted.
2.
7. CABLES - Use quality screened cables for signal connections.
3. COMPLY WITH WARNINGS - All warnings and instructions for
8. ƽ ꢀ RIGGING • SUSPENDING • MOUNTING
this product should be adhered to.
The rigging, suspension or mounting of this speaker system can
expose members of the public to serious health risks and even
death. UNDER NO CIRCUMSTANCES ATTEMPT TO RIG, SUS-
PEND OR OTHERWISE MOUNT THIS SYSTEM UNLESS YOU
ARE FULLY QUALIFIED AND CERTIFIED TO DO SO BY RELE-
VANT LOCAL, STATE AND NATIONAL AUTHORITIES. ALL
RELEVANT SAFETY REGULATIONS MUST BE FOLLOWED. IF
YOU ARE NOT PROPERLY QUALIFIED OR DO NOT KNOW OF
PERTINENT REGULATIONS, CONSULT QUALIFIED PERSON-
NEL FOR ADVICE AND ASSISTANCE.
Ɖ
4. Ꮨ WATER & MOISTURE
- This Wharfedale Pro unit should
not be used near liquids. If should not have liquids placed on or
in close proximity as there are ᏘDANGEROUS VOLTAGES
present.
5. ƽ VENTILATION/AIR FLOW: This Wharfedale Pro unit
should not have its heat sinks obstructed from air flow. It should
not be situated in a built-in installation that may hamper air flow to
the heat sinks. It should not be placed near heat sources.
9. Ꮧ CAUTION: These professional loudspeaker systems are
capable of generating very high sound pressure levels. Use care
with placement and operation to avoid exposure to excessive lev-
els that can cause permanent hearing damage.
6. Ꮨ POWER SUPPLY: This Wharfedale Pro unit should be
only connected to a power supply as stated on the unit. Power
supply cables should be routed where they will not be walked on
or pinched by objects placed adjacent or upon them.
10. SERVICING - The user should not attempt to service this
7. Ꮨ ELECTRIC SHOCK: Care should be taken that the ground-
product except that mentioned in this manual.
ing of this unit is NOT defeated. Do not use this units power cable
Wharfedale Pro EVP-P Series of Professional Sound Reinforcement Loudspeakers
● 200W RMS/320W Peak amplifier
● Hi/Low EQ control in the master section
● Integral tripod stand adaptor (except monitors)
● Balanced line output
● Combined Jack and XLR balanced input connectors
● Power on/off LED on front and back of unit
● Linkwitz Riley crossover for vocal clarity
● Heavy duty steel grille
(EVP 12P,12PM,15P,15PM)
● 300W RMS/480W Peak in EVP-15PSB only
● Built in 2 channel mixer with line and mic inputs
● Durable black carpet finish
● Integral High Frequency Driver Overload protection
“PRO-TECH” TM
● HF protection bulb
● Thermal overload, DC fault and short circuit protection
● Active crossover (EVP-15PSB only)
● Constant directivity HF horn
● 2 way trapezoidal ultra compact bass reflex design
Unpacking
Wharfedale Pro Limited Warranty*
Wharfedale Pro EVP-P Series loudspeaker systems are warranted to be
All Wharfedale Pro products are fully
clear of manufacturing or materials defects for a period of one year from
the original date of purchase. In the event of malfunction, contact your
authorised Wharfedale Professional dealer or distributor for information.
checked before leaving the factory. After
unpacking please inspect cabinets for any
physical damage. Please retain the ship-
ping carton if possible and internal packing
material in case the unit needs to be
returned. Please check as soon as possible the unit is functioning. In
the event of any damage please contact your dealer immediately so
that a written claim for damages can be made.
*Be aware that warranty details may differ from country to country. Contact your dealer or
distributor for information. These terms do not infringe your statutory rights.
Operating/Use
quality (see description and table of balanced line operation).
1. The EVP-P series has 2 XLR 1/4” jack Combi sockets.The two
stereo inputs are mixed down to mono enabling the connection of
stereo output products.
3. If using XLR CONNECTORS, insert the XLR until locked in. If
using a jack plug insert until secure.
2. Connect the provided power cable to the IEC mains connector
on rear of cabinet.
4. Power up audio mixer or processor ensuring connections are
made.
3 Connect the signal cable (balanced or un balanced, see table
and description) from audio mixer or processor securely to your
EVP-P unit (the internal amplifier should be off, power down
mode). Where possible use quality connectors. Only use
screened audio cable for the signal input from the audio mixer or
processor. If possible use balanced line signal leads for optimum
5. Power up EVP-P internal amplifier with levels on zero. Confirm
EVP-P speakers are operating.
6. The EVP-15PSB has 2 XLR/1/4” Jack Combi Sockets - one
line in, for system input and one line out for EVP-P as main speak-
ers. Two main loudspeakers may also be linked to one subwoofer.
|