R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Operator’s Manual
Manual del Operador
Manuel de l’utilisateur
RT10
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Read instructions carefully before assembling.
Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual del operador y siga todas las advertencias e instruc-
ciones de seguridad. Antes de ensamblar el producto lea cuidado-
samente el instructivo. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel de l’utilisateur et bien respecter tous les
avertissements et toutes les instructions de sécurité. Bien lire les
instructions avant d’assembler l’outil. Tout défaut de le faire pour-
rait entraîner des blessures graves.
Electrolux Home Products
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Mississauga, Ontario l5T 1K6
North America
Div. of WCI Outdoor Products, Inc.
Augusta, GA 30907
Copyright E2001 WCI Outdoor Products, Inc.
530086306
3/5/01
outlet. Do not change the equipment
plug, extension cord receptacle, or
extension cord plug in any way.
S To reduce risk of electrical shock, use
extension cords specifically marked
as suitable for outdoor appliances
having electrical rating not less than
the rating of unit. Cord must be
marked with suffix “W--A” (in Canada
“W”). Make sure your extension cord
is in good condition. Inspect exten-
sion cord before use and replace if
damaged. Do not use a damaged
cord. Cord insulation must be intact
with no cracks or deterioration. Plug
connectors must be undamaged. An
undersized extension cord will cause
a drop in line voltage resulting in loss
of power and overheating. If in doubt,
use the next heavier gauge. The low-
er the gauge number, the heavier the
cord (see SELECT AN EXTENSION
CORD).
ter recommended trimmer line (see
SERVICE AND ADJUSTMENTS). Never
use wire, rope, string, etc.
S Use specified trimmer spool. Make
sure spool is properly installed and all
parts are securely fastened.
S Use only Weed Eaterr replacement
parts and accessories as recommen-
ded.
CUTTING SAFETY
S Inspect area to be cut. Remove ob-
jects (rocks, broken glass, nails, wire,
string, etc.) which can be thrown or
become entangled in cutting head.
S Do not overreach or stand on unsta-
ble support. Keep firm footing and bal-
ance.
S Keep the cutting head below waist
level. Do not raise handles above
your waist. Cutting head can come
dangerously close to your body.
S Keep away from cutting head and
spinning line.
S Do not use multiple cords.
S Use unit properly. Use only for trim-
ming, scalping, and mowing. Do not
force unit. It will do the job better and
with less risk of injury at the rate for
which it was designed.
S Do not abuse cord. Never carry the
unit by the extension cord or yank ex-
tension cord to disconnect unit.
S Use cord retainer to prevent discon-
nection of extension cord from unit.
See ATTACH THE EXTENSION CORD
TO YOUR TRIMMER in the OPERATION
section.
S Use only in daylight or in good artificial
light.
MAINTENANCE SAFETY
S Do not use the unit if the switch does
not turn the unit on and off properly.
Repairs to the switch must be made
by your authorized service dealer.
S Keep the extension cord clear ofoper-
ator and obstacles at all times. Do not
expose cords to heat, oil, water, or
sharp edges.
S To avoid the possibility of electric
shock, avoid body contact with any
grounded conductor, such as metal
fences or pipes.
S Ground Fault Circuit Interrupter
(GFCI) protection should be provided
on circuit or outlet to be used. Recep-
tacles are available having built-in
GFCI protection and may be used for
this measure of safety.
WARNING: Disconnect unit from
the power supply before performing
maintenance, or when changing trim-
mer line.
S Maintain unit according to recom-
mended procedures. Keep cutting
line at proper length. Follow instruc-
tions for changing trimmer line.
S Have all service and maintenance not
explained in this manual performed
by an authorized service dealer to
avoid creating a hazard.
S Never douse or squirt the unit with wa-
ter or any other liquid. Clean unit and
decals with a damp sponge. Keep
handles dry, clean, and free from oil
and grease.
S Keep the air vents clean and free of
debris to avoid overheating the motor.
Clean after each use.
UNIT SAFETY
S Inspect unit before use. Replace
damaged parts. Make sure all han-
dles, guards, and fasteners are in
place and securely fastened. Parts
that are damaged must be repaired or
replaced by a authorized service
dealer. These include head parts that
are cracked, or chipped, guards, and
any other part that is damaged.
S Do not repair unit yourself.
TRANSPORTING AND STORAGE
S Stop the unit and disconnect the pow-
er source when not in use.
S Carry the unit with motor stopped.
S Store the unit so the line limiter blade
(on underside of shield) cannot cause
injury.
S Store unit indoors in a high, dry place
out of the reach of children. Store unit
unplugged.
S Use only 0.065 in. (1.65 mm) diame-
3
DOUBLE INSULATION
CONSTRUCTION
ATTACHING THE SHIELD
This unit is double insulated to help pro-
tect against electric shock. Double in-
sulation construction consists of two
separate “layers” of electrical insulation
instead of grounding.
Tools built with this insulation system
are not intended to be grounded. No
grounding means is provided on this
unit, nor should a means of grounding
be added to this unit. As a result, the ex-
tension cord used with your unit can be
plugged into any standard 120 volt elec-
trical outlet.
Safety precautions must be observed
when operating any electrical tool. The
double insulation system only provides
added protection against injury result-
ing from an internal electrical insulation
failure.
WARNING: The shield must be
properly installed. The shield provides
partial protection from the risk of thrown
objects to the operator and others. Your
unit is equipped with a line limiter blade,
which cuts excess line to the proper
length while running. The line limiter
blade (on underside of shield) is sharp
and can cut you.
NOTE: If shield is not properly installed,
damage to unit (including motor failure)
will result.
S Align the installation arrow on the
shield with the installation arrow on
the motor housing (see illustration be-
low).
S Insert the shield onto the motor hous-
ing. Ensure the cutting head remains
free to rotate and the line is not caught
between the shield and the motor
housing.
S Twist the shield as illustrated until it
snaps securely into place. Make sure
the shield is assembled to the unit as
shown in the illustration below.
WARNING: All electrical repairs to
this unit, including housing, switch, mo-
tor, etc., must be diagnosed and re-
paired by qualified service personnel.
Replacement parts for a double insu-
lated appliance must be recommended
by the manufacturer. A double insulated
appliance is marked with the words
“double insulation” or “double insu-
lated”. The symbol (square within a
ALIGN INSTALLATION ARROWS
square)
may also be marked on the
appliance. Failure to have the unit re-
paired by qualified service personnel
can cause the double insulation
construction to become ineffective and
result in serious injury.
SAVE THESE INSTRUCTIONS
ASSEMBLY
Twist shield
in direction of
arrow to
WARNING: If received as-
sembled, review all assembly steps to
ensure your unit is properly assembled
and all fasteners are secure.
assemble
CAUTION: Sharp line limiter blade
ADJUSTING ASSIST HANDLE
S Loosen wing nut on handle.
S Rotate the handle on the tube to an
upright position; place in a comfort-
able position and retighten wing nut.
4
S Cut from your right to your left to en-
sure debris is thrown away from you.
Without bending over, keep line near
and parallel to the ground and not
crowded into material being cut.
ADVANCING THE CUTTING LINE
Advance line by tapping bottom of cut-
ting head lightly on the ground while unit
is running at full speed. A metal line lim-
iter blade attached to the shield will cut
the line to the proper length.
OPERATION
Use only a voltage supply as specified
on your unit.
SELECT AN EXTENSION CORD
Extension Cord Gauge Chart
Length of Cord
Gauge
18 Gauge
16 Gauge
16 Gauge
25 Ft. (7.5 m)
50 Ft. (15 m)
100 Ft. (30 m)
To advance line, tap bottom of trimmer
head on ground one time.
Line limiter cuts
line to proper length.
TAP
Extension cords are available for this
unit.
ATTACH THE EXTENSION
CORD TO YOUR TRIMMER
Loop your extension cord through the
handle and around the hook as shown.
Insure the plug and cord are firmly and
fully engaged.
Cutting head
MAINTENANCE
Cord Retainer
WARNING: Disconnect power
source before performing maintenance.
GENERALRECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to oper-
ator abuse or negligence. To receive full
value from the warranty, the operator
must maintain unit as instructed in this
manual. Various adjustments will need
to be made periodically to properly
maintain your unit.
Extension Cord
CORRECT OPERATING POSITION
BEFORE EACH USE
CHECK FOR LOOSE
FASTENERS AND PARTS
S Housing Screws
S Assist Handle
S Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for
replacement of damaged or worn parts.
S Trigger Switch -- Ensure switch func-
tions properly by pressing and releas-
ing the trigger switch. Make sure mo-
tor stops.
Trimming
WARNING: Always wear eye pro-
tection. Never lean over the trimmer
head. Rocks or debris can ricochet or
be thrown into eyes and face and cause
blindness or other serious injury.
When operating unit, stand as shown
and check for the following:
S Wear eye protection and heavy cloth-
ing.
S Hold trigger handle with right hand
and assist handle with left hand.
S Keep unit below waist level.
S Debris Shield -- Discontinue use of
unit if debris shield is damaged.
AFTER EACH USE
INSPECT AND CLEAN UNIT AND DE-
CALS
S After each use, inspect complete unit
for loose or damaged parts. Clean the
unit using a damp cloth with a mild de-
tergent.
S Wipe off unit with a clean dry cloth.
5
STORAGE
SERVICE
REPLACING THE LINE
WARNING: Perform the following
S Disconnect unit from the power
source.
steps after each use.
S Remove the spool by firmly pulling on
the tap button.
S Stop the unit and disconnect the pow-
er source when not in use.
S Carry the unit with motor stopped.
S Store the unit so the line limiter blade
cannot cause injury.
S Store unit and extension cord indoors
in a high, dry place out of the reach of
children. Store unit unplugged.
S Store unit with all guards in place.
Position unit so that any sharp object
cannot accidentally cause injury.
S Clean entire surface of hub and spool.
S Replace with a pre-wound spool or
cut a length of 30 feet of 0.065 inch
(1.65 mm) diameter Weed Eaterr
brand line. Use of heavier lines could
overload and damage unit.
WARNING: Never use wire, rope,
string, etc., which can break off and be-
come a dangerous missile.
S Insert one end of the line about 1/2
inch (1 cm) into the small hole inside
the spool.
NEED ASSISTANCE?
For assistance or a replacement part,
call 1-- 800-- 554-- 6723.
Small
Hole
Spool
ACCESSORIES AVAILABLE
Safety Glasses
952701645
952701663
952701550
952701533
952701594
Tap
Button
Spool with 30! line
50! coil of bulk line
100! coil of bulk line
200! coil of bulk line
S Wind the line evenly and tightly onto
the spool. Wind in the direction of the
arrow found on the spool.
S Push the line into the notch, leaving 3
to 5 inches (7 -- 12 cm) unwound.
S Insert the line into the exit hole in the
hub as shown in the illustration.
Line in Notch
Line exit hole
S Align the notch with the line exit hole.
S Push the spool into the hub until it
snaps into place.
S Pull on the line extending outside the
hub to release it from the notch; other-
wise, the unit will not function properly.
6
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source before
performing all of the recommended remedies below except remedies that re-
quire unit to be operating.
TROUBLE
CAUSE
REMEDY
Trimmer head
stops under a
load or does not
1. Allow tip of line to do the cutting.
1. Crowding trimmer line
against material being
cut.
2. Contact your authorized service dealer.
3. Check breaker box.
4. Remove debris.
turn when switch 2. Electrical failure.
is pressed.
3. Thrown circuit breaker.
4. Debris stopping head.
Line does not
advance or
breaks while
cutting.
1. Check line routing.
1. Line improperly routed
in head.
2. Rewind line tightly and evenly.
2. Line improperly
wound into spool.
3. Incorrect line size
4. Not enough line
outside of head.
3. Use only 0.065 inch (1.65 mm) dia. line.
4. Remove cover and pull 4 inches
(10 cm) of line out of head.
5. Clean unit.
5. Dirt buildup on unit.
Line welds onto 1. Line size is incorrect.
1. Use only 0.065 inch (1.65 mm) dia. line.
2. Replace with correct spool.
3. Cut with tip of line fully extended.
2. Incorrect spool.
3. Line is being crowded
against material being
cut.
spool.
Line releases
continuously.
1. Line improperly
1. Check line routing.
routed in head.
2. Spool damaged.
2. Replace spool.
1. Line improperly routed
in head.
1. Check line routing.
Line usage is
excessive.
2. Line size is incorrect.
3. Crowding line against
material being cut.
2. Replace spool.
3. Cut with tip of line fully extended.
4. Spool worn or damaged. 4. Replace spool.
Line pulls back
into head.
1. Too little line outside
of head.
2. Line size incorrect.
1. Remove cover and pull 4 inches
(10 cm) of line outside of head.
2. Use only 0.065 inch (1.65 mm) dia. line.
7
sonable use during the warranty period.
This warranty does not cover predeliv-
ery set--up or normal adjustments ex-
plained in the Operator’s Manual.
THIS WARRANTY GIVES YOU SPE-
CIFIC LEGAL RIGHTS, AND YOU MAY
HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL
OR OTHER DAMAGES WILL BE AL-
LOWED, AND THERE ARE NO
OTHER EXPRESS WARRANTIES EX-
CEPT THOSE EXPRESSLY STIPU-
LATED HEREIN.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS
NORTH AMERICA, Division of WCI
Outdoor Products, Inc., warrants to
the original purchaser that each new
Weed Eaterr brand electric or cordless
product is free from defects in material
and workmanship and agrees to repair
or replace under this warranty any de-
fective Weed Eater brand electric prod-
uct within two (2) years from the original
date of purchase.
If your Weed Eater brand electric or
cordless product should fail within the
limited warranty period, return it, com-
plete, prepaid, with proof of purchase,
to the dealer from whom it was pur-
chased for repair or replacement at the
option of ELECTROLUX HOME
PRODUCTS NORTH AMERICA.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or the use of accessories
and/or attachments not specifically rec-
ommended by ELECTROLUX HOME
PRODUCTS NORTH AMERICA for
this electric product. Additionally, this
warranty does not cover parts that will
wear and require replacement with rea-
SOME STATES DO NOT ALLOW LIMI-
TATIONS ON HOW LONG AN IM-
PLIED WARRANTY LASTS OR THE
EXCLUSION OR LIMITATIONS OF IN-
CIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITA-
TIONS OR EXCLUSION MAY NOT AP-
PLY TO YOU.
ELECTROLUX HOME PRODUCTS
NORTH AMERICA’S policy is to con-
tinuously improve its products. There-
fore, ELECTROLUX HOME PROD-
UCTS NORTH AMERICA reserves the
right to change, modify, or discontinue
models, designs, specifications, and
accessories of all products at any time
without notice or obligation to any pur-
chaser.
8
|